MGB - Brake Booster Replacement

In my last post about Oliver, the 1978 MGB, I mentioned that the brake booster was the cause of a vacuum leak in the engine. This vacuum leak was causing cylinder #1 to run very lean compared to the others. Fortunately, Oliver has not seen much road time, so the engine should be fine. Regardless, today, I cover the fun of removing and then installing a replacement brake booster.

I would like to note that the body work on Zed came to a full stop when the Oregon weather predictably shifted back to cold-wet. For those who don't live here, we experience a wonderful donut-hole of beautiful weather in April/May smack in the middle of the cold-wet. The cold-wet returns for the month of June, usually lasting until Independence Day. So, I entertained myself with other projects, like this, while we waited for the weather to change back. After yesterday's high temps, I suspect the cold-wet is over until October.

Booster in an MGB

We start with where the booster lives in the small engine compartment of the MGB. The brake master cylinder, the clutch master cylinder and the brake booster all live together, attached to one another through the "pedal box": a rectangular steel box just in front of the firewall on the driver side. Closest to the rear is the clutch master cylinder. It is bolted to the back of the box with a lever extending into the box and attaching to the clutch pedal with a pin that is held in with a cotter pin. Attached to the front of the pedal box is the brake booster, with 4 1/2" nuts. This has a lever passing rearward, attaching to the brake pedal with a similar pin-with-a-pin design. To the front of the booster, the master cylinder is attached (2 nuts either 7/16" or 1/2"). Into the master cylinder a rod is passed from the brake booster.

You can imagine the brake action then: pedal is depressed which leverages against the clevis pin to press the lever into the brake booster. The brake booster converts some engine vacuum into more braking force which is then applied through the rod to the master cylinder.

Booster OUT OF an MGB

booster out

The Bentley manual has a step-by-step instruction for removing the brake booster, but I found the instructions to fall down. It started with removing the cover on the pedal box. I agree with that. It then described removing the clips for the brake lines leading to the master cylinder within the engine compartment. I agree with that. Then, it instructed to remove the bolts holding the brake master cylinder to the front of the booster. I also agree with that. At this point, the brake master cylinder can be slid forward off the booster-rod. By doing it this way, no air is introduced into the brake system. I likey.

Then, the instructions said to remove the cotter pin holding the clevis pin for the brake pedal to the leaver on the brake booster. This is not possible for anyone with adult male (and probably female) fingers for width and no one with child fingers for how deep you need to go. The gap between the side of the box and the partition which runs front-to-rear is not wide enough for fingers. I tried long needle nose pliers, but I concluded that even if I got the cotter pin free, and got the clevis pin off, I would not be able to re-install this way. So, I started my own path from here.

My plan was to remove the pedal box with the brake booster still attached and remove the booster from the pedal on my bench. Unlike the brake cotter pin, the partition is much wider on the clutch side, so my average-thickness fingers were able to remove both the cotter and clevis pins without too much difficulty. So, with the pedal disconnected, we remove the clutch master cylinder from the box by removing the 2 bolt/nut combinations that attach it from the rear.  Once removed, the clutch master  cylinder can be pushed rearwards out of the way. Next, we focus on the pedal pox. There are 2 bolts from the top, along the outer edge of the box nearest the centerline of the car. There are 3 bolts from inside the driver footwell going up. Last, there are 2 bolts from behind the dash running forward. Once all 7 bolts are out, the box is only held in place by gravity and the seal. Some light upward pressure on the brake booster and the unit pops free. Getting the unit out of the car took some wrestling, but I think this was more difficult because I could not see where the pedals were dangling. I found that by rotating the unit 90* clockwise helped the pedals to make it through the hole. had I read my old post about removing the pedal box (See MGB - Master Cylinders (Part 1)) or the post about the install afterwards (See MGB - Master Cylinders (Part 3)), I would have known to loosen the bolt fastening the clutch pedal so it dangled a little bit more. This would have made the removal much less of a muscle effort.

pedal box upside down on
workbench with old booster

Once the pedal box was out, it was a simple matter to remove the cotter pin and clevis pin between the brake pedal and the brake booster.... from the underside. I removed the remaining nuts on the brake booster, and started the install by performing the steps in the opposite order: attach the brake booster to the front of the pedal box. Thread the clevis pin through the lever and pedal, minding to include the washer before re-inserting the cotter pin.

Booster Back In MGB

With the unit in the same relative state of assembly as it was in when it was removed, I returned to Oliver to install it. I approached the install in the same manner as it was removed: rotated 90* so the booster was pointing across the engine. The pedals didn't fit, but with some rotating of the box and squeezing the pedals together, I could get them to fall through. Then, I wiggled and rotated the box, checking for cables wires and tubes from getting underneath until it settled in place. I decided that I would do the hardest first, so I did the clutch pedal/master first. I bolted the clutch master cylinder to the rear, after wiggling it around to fit, setting the lever alongside the clutch pedal. Then, I attached the pedal with the clevis pin and cotter pin. I found there was more play that I expected at this joint point, and concluded that I got the clevis pins backwards between the brake and clutch. Food for thought if you are doing this: the longer clevis pin is for the brake.

new booster in

With the clutch master cylinder tied in, I added the brake master cylinder to the front. This is much easier to get to. Once fitted, I started fitting the pedal box to the body. Because of the brake and clutch hard-lines, the pedal box is reluctant to move. I found that putting the 2 bolts through from the dash forward into the rear-most part of the pedal box allowed me to move the box into position. Once the bolt holes along the inside edge (2 of them, one 1/2" one 7/16") aligned, I set those 2 through. Last, I got back on my back inside the driver footwell and sent the last 3 7/16" bolts through the outer edge of the pedal box.

Brake Booster Hose

With the new booster on the pedal box and the pedal box in the car, all that remained was connecting the vacuum hose. I had oriented the booster upside down from the original so the vacuum nipple is on top, rather than below. I did this because of the significant heat source below the booster (exhaust) that is less present above. Also, the hose is much shorter and straighter from intake manifold bung to brake booster nipple. Wanting to avoid any possible issues with the original one-way valve on the intake manifold, I replaced it as well.

Re-Tune and Jetting

Because the old booster was creating a vacuum problem, I re-did the ColorTune tuning steps. Similar to the first time, I tuned using cylinders 1 and 3 but achieved a nice blue in both banks this time. I did swap out the idle jets (50F9 jets), but in order to find blue, I had the idle mixture screws further out than 2 full turns. I will drive Oliver around a little bit, but I think I may need to go up to 55F9 jets if the instructions in the SK Racing manual are to be followed. I noticed that the SK Racing product page describes the "pilot jet" in the carb set-ups they are selling today as 55. Assuming this is the idle fuel size, that's more support for trying 55F9 idle jets.

Since these SK Racing carbs are so similar to the side-draft Weber, here's another tuning link I found specifically for Weber. Notice how that article indicates the starting spot for the idle mixture screw is 2.5 turns out? That is about where mine are now. Curious. One last link, again on the much more plentiful Weber DCOE, but this time about some recommended jet sizes. It recommends the 50F9 idle jets for a late B like I just put in, so honestly, at this point, it will come down to a road test.

under the jet cover plate

Swapping out jets in this carb is seriously one of the easiest things I think I have ever done on a car. There is a cover plate on the top of the carb which is held in place with a slotted bolt. Once the cover is removed, the 4 jets (one idle per side and one main per side) are held in with slotted jet holders. The idle jets are the ones further from the engine / closer to the air filter. The holder threads out, and the jet is held in the holder basically with friction. The old jet slides out, the new jet pops in and you thread everything back together again.

The engine tune did not meaningfully change after the re-jet, so I concluded that the air-fuel mixture from the old jet was virtually the same. So either I removed a pair of 50F9 jets only to put in new ones or the old ones were a similar enough combination that they provided the same air-fuel at idle. At least I know what they are now.

All that is left is a drive... but wait! I didn't hook up the brake light switch. Well, I did, and after a few days of head-scratching trying to get the lights to illuminate, I realized that I had plugged it in wrong. The source 12V arrives in a dual plug, and the signal to the brakes departs through a single plug. I had thought the single plug was from the old carb-preheater, so I had failed to send either side of the switch to the brakes. Instead, I simply wired both sides of the switch to the 12V supply. Hahaha. Simple fix. Once the cars were shuffled so Oliver could get out past the herd, I did a longer test-loop. It did not take long to get the engine to normal operating temperature and he ran great. There was a slight stumble (bog) from dead stop, indicating that he was still a little lean. So, once back in the garage, I turned the idle screws about 1/8 a turn more rich. When I rev'd him from idle, I could not note a bog so I figure he is fairly close to tuned now. More road testing will confirm, and I expect I will fiddle with these screws as weather and altitude factor.

Thanks, as always, for following along-

MGB - Finding Vacuum Leak

Following my last post about Oliver (the 1978 MGB) when I got his timing square, I knew I needed to get his carb tuned. Today's post covers those efforts. This continued in parallel with the body work on Zed (until the weather turned, when Zed work stopped). These spring days, when the sun doesn't go down until 9PM creates LOTS of play-on-cars time. Love it.

A-typical Carb

We start with the most basic learning: what kind of carb is this? When I bought this car, the prior owner had been executing some improvements. For the most part, I can't complain about any of them... except the hack-job on the exhaust. Honestly, he could have been just making do until he had the cabbage to do what I did. Anyway, one of the improvements was to eliminate the stock dual Skinner Union (SU) carbs and swap in a side-draft carb. This isn't your standard Weber DCOE, though. Instead, the prior owner went with a SK Racing carb. The SK Racing (now known as OER Racing) side draft carb was (according to Dog283) one of the best engineered side draft carbs built, just as carburetors were falling out of favor for the new computer-assisted fuel injection systems. Dog283 continued "(the SKRacing side draft) combine(s) the best of the the Mikuni Solex PHH, the Weber DCOE and the Dellorto DHLA". That's a fairly strong statement. Unfortunately, the implementation on Oliver had fallen out of tune, so our MGB was not getting the lofty results this statement describes.

We start with looking for, and ultimately finding, a shop manual for the SK Racing side draft carb. If you have one of these carbs and need a copy of this manual, I'll happily share it. Near the back of it are the set-up steps detailed in the image of the page on the right. Basically, set the idle speed screw so it is just barely touching the tang, thread the idle adjustment screws all the way in until they just barely seat and then rotate them back out 1 full turn. Start the engine and get it to normal operating temperature. Then, tune the adjustment screws first until the engine runs smoothly, then set the idle speed. I did that, but I still got sporadic backfires when I rev'd the engine. I was starting to think that all that ignition work was for nothing.

Exhaust Leak Checks

Before I started investing time in the carb, I figured it would be a good idea to see if there were any leaks in my exhaust which could account for the backfiring. There were. To test, I started by cleaning out my shop-vac (washed out with a hose) and grabbing a squirt bottle of soapy water. I thrust the exhaust end of my now-clean shop-vac up the tail pipe and turned it on. This created backpressure through the exhaust. The tail pipe was not completely blocked so lots of air rushed right back out, but there was enough pressure to execute my test. I started up front, in the engine compartment and shot soapy water on the mate-point between the header and the head. No bubbles. I then got under the car and hit every joint, and found some bubbles. I concluded that I created leaks when I added in the catalytic converter. I turned off the shop-vac, loosened the joints, slid the pipes apart and applied some copper exhaust gasket maker and then re-connected the pipes. I nutted them back down and re-checked with the shop-vac. Things looked fixed (no bubbles at all but one joint where there were very very few), so I moved on to tuning, expecting my backfire issues had been identified and resolved.

Gunson ColorTune

Back when I was doing the other work on Oliver, I kind of expected difficulty with getting the carb to adjust. So, before I finished getting the ignition installed, I ordered a Gunson ColorTune. These things are pretty neat, but not terribly useful, I suspect, for the computer-controlled fuel injected systems. The kit includes a looking-glass spark plug, a lead, a tube with a mirror and a brush. I only needed the glass spark plug and the lead. The looking-glass has a solid-center where the spark is produced, with a ring of glass around it. The glass ring is then encircled with threaded metal so it can be threaded into an engine. The tube with a mirror is for spark plug holes that are hard to see. To use the kit, you remove one spark plug and thread the looking-glass plug in it's place. You connect the spark plug lead to the end of the lead from the kit, which is threaded onto the glass plug. Then, you start the engine and look at the color of the combustion in the chamber through the glass. If the color is orange or red, your mixture is too rich. You want the color to be "Bunson blue" = the color of a Bunson burner, from, like science class. The images on the right, here, help lead you to a good tuning. Notice that light blue or white-ish is not on here. If you are in the white-zone (Airplane, the movie reference here), your tune is too lean.

I was unable to get cylinders 1 and 2 anything better than a very light blue even after adjusting the idle mixture out past 1-1/2 turns. Cylinders 3/4 did not do much better. Based on the manual, I believe the idle jets may be too small, so I ordered a pair of 50F9 jets ($7US each). If I am correct, the current idle jets are 45's and this change will allow idle-mixture within 1-1/2 turns of fully seated to sit in the Bunson-blue color.

Still, I kept going, wanting to get the tune as good as I could. While looking through the glass I increased the fuel mixture incrementally, but the misses and backfires persisted. I could see the backfiring through the glass in cylinder 1, and concluded there had to be a leak somewhere. I also figured that backfires within a cylinder that has a glass plug was probably not a good idea. I had already looked on the exhaust side for leaks, so that left the intake.

Intake Vacuum Leak Checks

There are not many places where a leak could appear in the intake: the mating point at the head, the mating point with the carb, the carb itself and the brake booster. With the engine running, I carefully sprayed some WD-40 onto the various mate points. If there had been a vacuum leak, the vapor would have been drawn into the engine and the RPM would have bumped in response. Spraying something flammable onto a hot engine is dangerous. I strongly urge you to keep a fire extinguisher handy if you do this. In my case, the engine did not change and nothing caught fire.

So, I shut everything off and considered the brake booster. I removed the hose from the check valve, which is threaded into the intake manifold heading to cylinders 1 and 2. I checked the vacuum of the brake booster through that hose with the MityVac. It would not hold vacuum. I removed the check valve and cleaned the valve and the intake manifold where they met. Then, I put some copper gasket maker on the threads of the check valve and threaded it back in. I figured if that was the leak, I just solved it. I jabbed the hose back onto the check valve and hose-clamped it tight. Then, I eliminated the brake booster by threading a bolt into the end of the hose which had previously been attached to the booster, and started the engine. Oliver ran great! I could rev him up and down without any backfires demonstrating that the brake booster was my vacuum leak.

check valve in foreground,
intake in background

I wanted to prove it for sure, so I hooked the booster hose back up to the brake booster and started the engine again. I rev'd the engine up and down... the back fired returned. I pinched the vacuum hose with a pair of pliers and I could hear the engine RPM's settle. Neat. Rev rev rev... no back fires. Remove the pliers, RPM increases... rev, rev, rev... backfires.

Fortunately, these brake boosters are being manufactured now. I didn't realize these were not available until recently, so as much as I would like to self-blame for not replacing the booster when I replaced the brake and clutch master cylinders, it wasn't available then and they are fairly expensive now (~$200US). As of today, they are not available through Moss yet. I had to go through another vendor (EnglishParts.com, they're lovely). I concluded that any carb tuning I had done would need to be redone once the brake booster swap was completed. 

That's it for today. I will install and post about the brake booster when it arrives from the MidWest. Thanks, as always, for following along-