Showing posts with label support. Show all posts
Showing posts with label support. Show all posts

Tuesday, January 27, 2026

Hapy Re-Assembly Continues

First, thanks for following along. I know blogs have fallen far out of favor, with videos and such being the preferred means for getting information. I can't watch videos at work, but I can read, so for me, this is still viable. There's an old saying about not having a face for video, or a voice for radio, you can still print. That's me. Besides, I barely have time to do my thing and write about it, much less shoot and produce video. I don't know how those content producers get any sleep, especially the ones who aren't making any money at it, which, lets be honest, that's most of them. More power to them, and I greatly appreciate their efforts. When I finally wind down at night, I love me some car-fixin videos.
 
So, where were we? Oh yeah, Hapy was almost assembled. Well, his engine and transaxle were mated and they were mounted to the bus. That's the fun, exciting, sexy part. What's left is everything else. I stayed under the bus and finished everything there first before getting after the from-above stuff. I didn't take any pictures, mostly because with all the extra layers simply moving around under the bus is a challenge.
 
Transaxle Finish
I started at the front and worked by way backwards. This started with the nose-mount. At some point when the transaxle was removed, one of the mounting bolts broke off inside the threaded body mount. I know I need to resolve this, and practically every time I get under the bus, I shoot that broken-off bolt with some penetrating oil. I believe the front mount carries very little actual weight, but it does make sure the transaxle remains aligned. I gotta get that bolt out and replaced, but not today. With the one bolt in, I connected the grounding strap. I slid to the left side and connected the Bowden tube and clutch cable. I make a point of leaving bolts partly threaded into where they go so (a) I don't lose them and (b) so I know where they go when I return to a project 6 months later. This made installing the Bowden tube just the usual challenge and not accentuated with a bolt search first. To make the threading of the butterfly nut on the end of the cable easier, I prop up the clutch pedal and then put vice-grips where the cable meets the threaded end. Lots of tightening later, I then test the play of the pedal and slide back under a few times to make sure the pedal has an inch or so of travel before the pedal meets resistance.
 
The last thing on the transaxle is the reverse light plug. In my efforts to install, I smashed the reverse light plug quite a bit. Perhaps this happened when the transaxle fell of the jack this past summer. Hard to know. Anyway, with needle-nose pliers I straightened them out. The leads, have been in the same position for so many years that they were already pre-oriented for the right spots to plug in. 
 
Rear (Anti-)Sway Bar 
Sliding further rearward, I got after the rear sway bar. I will again mention how helpful this bar has been for handling, especially in a strong cross-wind. I will also stress how important it is to have it out of the way for a transaxle R&R. I raised the center of the bar with the TravisJack so I could use both hands on the various mounts. I made sure to put a small smear of clear, hi-temp grease (not black axle grease) on the hard bushings, finger-threaded everything and then nutted every thing down. The grease extends the life of the hard bushings, by reducing the direct-wear of hard bar twisting against them. I had not greased these previously, but we really have not run more than a few hundred miles since I put this bar on.
 
Starter
Now we're getting near the end of the below-the-bus stuff, with the starter going in. With the newer starter adapter, with the studs to hang the starter on, the install is much easier. It really is as easy as popping on there and nutting down with a 17mm socket. The top nut can be a challenge to reach, but the rest of it is easy. Pop on the 12V send from the battery and the 12V send-to-front onto the main post, nut down with a 14mm. Last, pop on the starter trigger. Done. Next!
from warmer summer days

Before sliding out, I hooked up the ground from the right side of the engine to the frame.
 
Fueling
For the most part, I left the fuel system in-tact. Right now, I start to feel the advantages of not pulling the motor all the way out of the engine bay. All I did to enable this job was remove the big Caterpillar fuel filter from the frame, and drape it on the engine. So, a couple of bolts later, the fuel system is back together, hopefully holding prime.
 
Cooling
Similar to the fueling system, I minimally disconnected the cooling system. So, I thought it would be just as easy. I lifted the overflow bottle and noticed the bottle was low, and could hear splashing noise coming from the driver side. I lowered the bottle and the steady stream stopped, so clearly there was a breach up higher in the system, and not a breech in the radiator cooling lines or something that would have potentially cost me all of the coolant. Sure enough, the coolant temperature sensor that plugs into the coolant outlet flange was loose and the c-clip was no where to be seen. It is highly likely that the clip was lost last Summer. At this point, I ordered a replacement, and moved on, but not without laughing at how, again, the coolant outlet flange bit me again. 
 
Charged Air
All I removed from the charged air system were the 2 silicone elbows that connect the inter-cooler to the system. Then, the inter-cooler can be moved out of the way for the work. The silicone elbows are held in-place with large clamps that require a special tool (or lots of patience with channel-lock pliers). I used both. Once complete, I noticed that the little blower fan I have on the inter-cooler was barely clinging to the inter-cooler so I fixed that with some new zip-ties. I intend to one day replace the air-to-air inter-cooler with an air-to-water system, reducing overall inbound air temperatures and freeing up some engine compartment space.
 
This was as far as I could really go without that little clip. So, this is where I stopped while waiting for them to arrive from ECS Tuning. While waiting for the coolant temperature sensor c-clip to arrive, I put the battery on the charger. Next time, we'll get after that little clip and whatever other adventures we uncover.
 
Thanks, as always, for following along- 
 

Tuesday, January 13, 2026

Hapy Re-Assembly

I have been waiting to do this post until after Hapy was completely back in one piece, but after many hours and days out there, he is still not quite together. Still, seems like as good a time as any to update, and, like seems to happen so often, this got long, so this is going to get split out. Perhaps he will be in one piece by the time I get the next post done. Anyway, I left off last time after having moved Hapy from the sloped and badly cracked driveway into the shop. That was in early October. With extreme work expectations, I had very little free time, so there he sat until winter break (mid-to-late December).
 
Time to Lean, Time to Clean
engine in, oriented
First, I moved the ATV jack with my wooden cradle under the engine and supported the engine. I started by removing the ratchet-straps I had used to hold the front of the engine to the frame and the axles from dragging on the ground. Then, I removed the rear mount, support tower and cross-bar. Last, I removed the rear tow-hitch / rear bumper assembly.
 
I was on a cleaning adventure, so I cleaned the engine bay and the parts I had just removed with de-greaser. Then, I painted those parts and the underside of the bus's rear end and lower engine bay with Eastwood's rust converter. I felt this set the stage for a less filthy job. Since I failed to clean the engine, however, I was only half right. But, the parts which were painted look really good now and I hope the rust growth is at least slowed, if not stopped, by the application of the rust converter. As they say "rust never sleeps" so it will remain on the inspect-every-time list regardless.
 
Transaxle Together
output flange going on
We start our assembly adventure by just returning the transaxle back to its state before I removed it. Recall that during my efforts to get the transaxle and engine to mate on the cracky driveway, the transaxle awkwardly fell off a small jack and onto the concrete, causing the left (driver in US) side output flange to pop off. This was what put the re-assembly effort into dead stop last Summer. After getting some advice, a new plastic cover and a few packets of grease from a shop around the way, I again did nothing about it for weeks. Work has been all-consuming this year, did I mention that? Anyway, continuing my cleaning frenzy, I cleaned everything (except the engine, it seems): the transaxle, the various parts, the area I was going to work in, my tools... you get the point. The little c-clip that was responsible for holding the flange to the transaxle was a little bent from it's rapid extraction by the driveway. The shop owner suggested that the original clip was higher quality than the EMPI stuff on the market now and encouraged me to flatten/fix that clip. So I did, with a vice and a hammer. With the mating points all clean, and the old little plastic cover gone, re-attaching the output flange, setting the c-clip and then setting the new plastic cover actually took as long to do as it just took to type. I was stunned it was that easy and felt rather stupid for avoiding this for, like, 6 months.
 
While I was there, I also took the shop owners other advice about removing the throw-out bearing, greasing the slide and re-installing the throw-out bearing. While the parts were apart, I hit the teeth on the output shaft with a wire brush, getting all the gunk out of the teeth. With the transaxle now back in one piece, I set it on a big sheet of cardboard and slid it under the bus, from the rear around the left side of the engine and over the rear sway-bar lying on the ground. 
 
I will make an aside about the rear sway-bar here. While it is great for handling, it is awful for getting the engine/transaxle in and out. It really is great for handing, though, especially in windy conditions. Simply disconnecting the frame mounts and letting it hang on the ground, leaving the shock mount ends connected, makes for a tall, virtually uncross-able, speed-bump for your floor jack. In the future, when I (and I suggest any reader who has the rear sway-bar) remove my transaxle again, I will completely remove the rear sway-bar from under the bus, leaving the space completely clear.
 
Tranny Meet Diesel
strapped to rotate
With the transaxle on the ground under the bus, I set to mating it to the engine. Right here is when I wish I'd remembered a few things:
1- while you can still interact with your transaxle, put the little cage on the shifter rod that comes out the front. I didn't and while it still isn't done yet I have already spent an hour trying to get the grub screw to thread in after the transaxle is already installed. Word to the wise: do this beforehand.
2- that shifter rod goes OVER the rear main frame tube. I don't know what it's real name is, but you need to put that rod over the tube before you try to put the transaxle into place. I forgot, mated the engine:transaxle and then had to do it again because I could not get the engine far enough back to get the shift rod over the tube. Total facepalm. Lost hours facepalm.
 
I am going to draft on this moment and drop a placeholder for consideration: Cutting in a removable rear valence like the earlier bus's had. I know the engineers made the fixed, permanent valence for structural integrity. Any other 1972 and later bus might still require it. For that matter, this bus may still require it. My bus, my risk ; I encourage others to not follow this advice without giving it some serious thought and even then, ask friends. My bus has 2 additional side-to-side heavy bars bolted into the side frames: one for the rear engine mount and one for the rear tow hitch. Both of these are heavy steel bars bolted in separately from each other. I submit that if I cut the rear to have a removable valence, I would suffer no structural loss. So, I think the next time I need to remove the engine, I will give this serious thought. How I do it so it doesn't look trash will be the fun part.
 
Anyway, once I got the shift rod over the tube, I set the transaxle on the "race" jack I got from our dearly departed brother-in-law, Travis (and named it accordingly). With the transaxle easily balancing on the Travis I was able to get the output shaft of the transaxle to align with the clutch. It is noteworthy that I did not use the "small" jack the transaxle fell off of this time; the big pad on the Travis is way more stable. I got the 2 to mate and threaded in 4 bolts to snug them together: 2 on the very bottom, one just above the clutch throw-out arm and one which threads through the starter mount.
 
Central Mounting
With the engine and transaxle as one large and heavy assembly, I needed to get it aligned with the 2 central mount holes: the 2 which pass through the ears on the top rear of the transaxle. I believe this mount handles the lion's share of the weight. The left side aligned fairly easily (20 minutes of wrestling) but it took a couple of hours of fighting the right side. I could not remember having such a hard time reaching and seeing. With a shrug, I went to put things away and noticed that I could not lower the overhead engine lid I'd cut in all those years ago. It was bopping on the intake. I realized that the engine and transaxle were clocked for an upright install, not a "stock" orientation (same tilt as native install in a Jetta or NewBeetle) as I had before. I had mated the engine and transaxle wrong. I called it a day, and took a long shower.
 
For Clock's Sake
nearly buttoned below
I have some of my best (and sometimes worst) ideas in the shower. I figured that I could put a ratchet strap around the front of the engine, hooking the ends on the frame like I had it when I moved the bus, and use the webbing as a cradle for rotating the engine, re-clocking it against the transaxle. Suspending the weight of the engine on some webbing was not going to be enough so I put in the rear engine mount cross bar and tower. Then, I connected the engine mount to the engine, letting the body-side of the mount float free. As an extra precaution, I moved the ATV jack and cradle under the engine and raised it so it was just below the engine. Then, I put the ratchet strap in place and cranked it down as snug as I could. Feeling a little anxious, I removed the 4 bolts and nothing moved nor settled at all. So, feeling bold, I grabbed the engine by the alternator mount with my right hand and the turbo with my left and slowly rotated the engine anti-clockwise. I was able to key off of the bottom bolt on the left side, switching from on my back with the bolt in hand to on my feet and shifting the engine and back again. Ultimately, I found that using a small screwdriver to help fine-tune the bolt location was most effective, but once I had that one bolt, the upper left and starter-bolts went in easily. I was unable to seat the lower right bolt and I will have to go through my notes to see how many bolts I've used before to see if I'm chasing something a false memory of 4 bolts.
 
Once the bolts were through, I removed the ratchet strap, wrenched down the engine mount on the engine side and then connected it to the tower. I am going to stop here, mostly because this is as far as I've gotten. By next time, I will have solved the grub-screw in the shift linkage and have the rest of Hapy put together. I hope I will even be able to tell a tale of a test run.
 
Thanks, as always, for following along. I know my posts have become few and far between. We had some staffing changes at my employer late in 2024 and that meant lots more work for me ever since. I do not anticipate that significantly changing, so my attitude about it needs to. Working on it.

Wednesday, July 9, 2025

Hapy Engine-Transaxle Dropped

Around the concrete work, I ordered a replacement flywheel, clutch and pressure plate from Kennedy Engineering for Hapy (TDI-powered 1972 VW camperbus). The flywheel entered fabrication early last week, so I spent part of the Independence Day weekend dropping and separating the engine and transaxle not-in-a-shop for hopefully the last time. Today's post covers the drop and separation; it took 10 hours spread across 2 days.
 
How Did We Get Here
hockey player smile
I have been queuing this most recent engine drop for over a year. Recall all of the starter swaps I have made in hopes of solving the intermittent starting issue. And, I replaced the starter adapter hoping that was the issue. Nope and nope. The flywheel had suffered sufficient incomplete meshing of the starter gear with the flywheel's ring gear, chipping teeth and wearing down others. During my research, I learned that oftentimes (not always) engines will tend to stop running at the same spot in their rotation. So, if the circle is 360 degrees, the engine will stop most of the time at the same point. I know that seems counter-intuitive when you assume an engine is a well-balanced smooth machine, but the 4 cylinders and the 4 steps in the combustion cycle create a frequency, if you will, that for some engines means that when you kill power it will naturally stop at the same point. In those cases, you would think having a complete ring gear is unnecessary, right? I mean, if you only ever use 15 degrees of gear, why have 360? Ok, in re-reading this, obviously you need an entire gear for the starter to spin the engine. LOL.
 
I found on my flywheel there was one spot in particular which was especially bad and 3 other spots which looked like there was wear, but not so much that the starter was really having trouble. This would explain why all the other times I looked at the flywheel I could not see an issue. The starter was not on the really bad spot, just one of the not-so-great spots. When I was unable to get the engine to start on the first try, but I got the gear-on-gear sound, I think I was starting on one of those spots. Inevitably, the engine would eventually land on the really bad one, and the sound would change from gear-on-gear to gear-in-the-air. 
 
Continuing this nonsensical thread, the TDI engine's flywheel can only fit on the engine one way, based on the bolt pattern. If there were any way I could have retained the flywheel and simply removed and re-installed it so that the really bad spot was in one of the zones where the teeth are never facing the starter at dead-stop... I would have. I mean, this flywheel has lasted 15 years of starting issues and abuse and for the most part it's fine. Well, fine except for the 1 big chunk that's missing and some other kinda-worn spots.
 
Getting Down
So, we enter Saturday, July 5th, the traditional first day Pacific NorthWest summer, tools in hand, blues festival on the radio, ready to get after the engine drop. To prepare, I re-read the last engine drop I can remember doing on this bus: to swap the transaxle from the original 002 to the AA Transaxle (Seattle) 1975 CM 002 transaxle. I did that on Labor Day 2012 in my real estate agent's driveway (See Transaxle Transition). It took 1 day to get the engine/transaxle out and separated. It took 1-1/2 days to get the new transaxle mated and the whole operation installed. I figured I would have a similar path, but my real estate agent's driveway was flat and smooth. The square of concrete outside my tiny garage is neither flat nor smooth. Quite the opposite, actually, it slopes away from the garage slightly and it has massive deep cracks in it. Like 2 or 3 inches deep cracks where blocks of concrete are lower/higher than the section next to it. This makes moving an engine on a jack much harder.
 
air disconnected
High level, my plan was to not raise the bus, and to only remove that which was necessary to allow me to separate the transaxle from the engine (and the bus) so I could do a clutch service with a flywheel swap out. So, I chocked the front tires and got after it. I started with the easier stuff: disconnect the air side first (cold air/filter to intake, unplugging the AFM and a vacuum line, then removed the charged air from turbo to intercooler). Then, the 13mm nut/bolts on the exhaust side of the turbo and removed the exhaust. Since I did not have to really move the engine other than up and down, I chose to leave the coolant related systems alone other than disconnecting the overflow bottle to prevent tension on the hoses. I made the same decision wit the fueling system, and chose to only disconnect the large filter, again to eliminate potential tension on the fuel hose. Last thing on the engine was to disconnect the battery and the 12V exciter from the alternator.
 
Shifting to the transaxle, I set a small jack under the center of the ribs and started removing things. First, I removed the CV joints and stuffed the greasy bits into plastic bags held on with rubber bands. The clutch cable and the mount for the bowden tube were next. Once free, I disconnected the shifter at the front of the transaxle, the grounding strap near the front and finished with the nose mount. At this point, the only things connected to the engine/transaxle I needed to address were the rear engine mount and the main carrier mounts.
 
simple coolant solve
I located and set the engine cradle on the ATV jack and supported the engine while I removed the rear mount and the tower between the support bar and the mount. With the engine supported, I removed the 2 bolts which attach the top of the bellhousing to the main center carrier.
 
Well, Now Its Down
This was all I thought I had to do to drop the engine. When I read the old steps, this was how far I had to go. Since then, however, I added the rear sway bar and it was set such that removing and then re-installing the transaxle was going to be more difficult. I removed the 4 14mm nuts that held the middle of the bar to the frame and it swung down far enough for the transaxle nose to clear. But there was not enough room for the shifter linkage above the side-to-side main support to clear. The engine needed to move backwards a couple of inches. So, I removed the rear engine support bar. In retrospect, I realized that I had removed that bar last time too. Now, I could pull the engine far enough back to get the transaxle off of the engine, rotated and then onto the ground. Sitting on cardboard, I pulled the transaxle out the driver side. I regret not taking a picture of the inside of the bellhousing, but it had so many little metal flakes (from the flywheel). I shot the bellhousing with brake cleaner and then, after I had wrapped the cv-joint mount points with plastic film, I shot the whole transaxle with de-greaser. I hosed it off and let it dry in the sun. While I had the de-greaser out, I cleaned the rear engine support bar too.
 
Pressure Plate and Flywheel
jack on crack
Now, I was basically ready for a clutch job. The pressure plate came off with little fanfare. It looks like its in great shape. The clutch still has most of it's friction material, so in a pinch I could probably reuse them. I got new replacements for both, so I may retain them for an emergency. Honestly, after 12 years of running this clutch and still have that much friction material left, I figure I may not have to replace this clutch ever again. I did notice a couple of spots on the flywheel which had a slight blue-ish hue, though. That's usually a sign that the clutch got hot and sticky. Something to think about. Maybe going with the stage 1 clutch this time rather than the stock pre-1972 VW bus clutch was the right call after-all, and the old clutch/pressure plate are not worth keeping.
 
Last, I had to pull the flywheel. Fortunately, I have a flywheel lock for old VW's and since this is a 200mm flywheel designed to fit inside a 002 transaxle, the lock fit. I could not get good leverage lying on my back under the bus so I smacked a rubber mallet against the end of a ratchet to pop the torqued bolt. All 6 came out without too much trouble. Applying a torque wrench on install will be interesting. Because of how snug the flywheel mates to the engine output, I needed to work the flywheel off with a small prybar. Once on the ground, I could more clearly identify the really badly worn spot (pictured above), but the other spots did not look as bad. Perhaps, once I have the new one to compare, the damage on this flywheel will be more apparent.
 
Conclusion
no downhill roll please
That's as far I've been able to get. I am still waiting for the flywheel, clutch, pressure place, throw-out bearing, etc. It took me most of 2 days to get to this point, so I expect the re-install will be similarly extended from 1-1/2 days to maybe 3. It is interesting to see how an uneven surface and 12 years of personal aging can slow a process down. The sway bar and engine support bars each represented maybe an hour of extra work, so I can't attribute it to them. This is probably really about me getting slower and the work location making everything that little bit harder.
 
For those tracking on the shop construction, we may be falling onto their schedule as early as the end of next week. Fingers crossed, I may have a structure before I have Hapy back in one piece. 
 
Anyway, that's it for today. Thanks, as always, for following along-