Showing posts with label progressive. Show all posts
Showing posts with label progressive. Show all posts

Saturday, August 17, 2013

Rack 'em, Snow Bum

Sure, I know its August.  Yep, most folks are taking vacations or at the least thinking about the sweltering heat.  Even here in usually-temperate Oregon, the humidity has been over 65% (which is downright humid for these parts in August).  Sweaty.  It reminds me of my old lawn-mowing days in upstate New York with 80%+ humidity, 80*+ temps.  To combat the weight of the dog-day heat, I think cool thoughts.  T and I will talk about the drop into the bowl on the Thunder run at Timberline or Ski Bowl's Lower Surprise trail.  It's funny how talking about losing an edge and cartwheeling downhill in deep powder can cool you off.  I spent yesterday afternoon in my 90* garage building a ski/board rack for the bus.  I'll detail that today.  Stay cool my friends.  2013-2014 Fusion season passes go on sale in less than 3 weeks (Sept 3rd!).

Starting with What?
thinking about it
The bus was a 1972 Westy when I first bought it.  It ran a 1700CC air-cooled non-original engine with a Weber 32/36 Progressive carb, 009 dizzy and a worthless heat-exchanger exhaust (65HP, 18mpg @best).  It had the original 1972 Westvalia interior and canvas bellowed pop-top.  Today, it runs a 1.9L TDI from a 1998 New Beetle (90+HP, 30mpg).  Inside, it has the rock-n-roll bed, rear closet and refer cabinet from a '79 Westy plus a middle row seat from a Vanagon.  Up top, it has a 1972 Riviera (straight up) poptop and bed.  That may sound crowded inside, and it can be.  Since I've been working on the engine, I have had the rear closet (left side with a front-facing door and cubicles at the rear) out of the bus and sitting in the garage.  This leaves the engine electronics, which sit in the spare wheel well, exposed.  I have a solution for that, but that's for another day.  Anyway, I started looking at the 14" gap between the left side wall and the middle row / rear seat, thinking.... "couldn't we put our ski stuff there?"....

Think, Measure, Think
aligning the rails
I started simply by setting a shoe box on top of the refer cabinet and putting my snowboard on top.  Surely I could make something work there.  I grabbed a set of skis and held them above.  "Yep, I should be able to make 3 racks, each holding either 2 boards or 2 sets of ski's," I thought.  The racks need to be far enough apart so snowboard bindings fit between them, but close enough together so our youngest ski's fit.  That last part proved too much, but he needs new planks anyway, so it should all work out.  Holding the ski's in the air, I made pencil marks on the wall to give me a sense as to where the rails should sit.
I wanted the rack to have some give, so I chose to connect the rails to the side supports with hinges rather than angle braces.  On the other end, I thumb-screwed eye-hooks so we could pull one-to-all of the racks upwards, suspended from another eye-hook in the ceiling by a length of chain.  I haven't completed that part yet.  Last, the equipment needs to stay put.  To address that, I replaced one hinge wood-screw on each rail with a eye-hook bolt run through to the bottom.  On each rail, a 12" bungee is attached from hinge eye-hook to rail-end eye-hook.  I am waiting for the arrival of some bath-tub tread material that I will apply to the rails to make it complete.
parts list

Material List
2 6' lengths of 1x3 cedar for the side supports and rails.
3 packs of 2" utility hinges (2 in each pack)
3 packs of #8-32 x 1-5/8" eye-bolts (2 in each pack)
3 packs of #208 Screw Eyes (2 in each pack) - for rail ends
1 pack of #206 Screw Eyes (2 in pack) - for ceiling
1 8-pack of mini bungee's
some #10 washers

Cuts and Drills
I started with a clean-up cuts on the ends of the cedar.  Lumber yards don't make perfect square cuts, so this is always a good idea.  I cut 2 24" long pieces for the supports and 6 12" long pieces for the rails.  I set one of the supports against the sidewall to consider rail placement.  To make it simple, I pressed the support against the headliner support.  I transferred the pencil marks on the wall to the support. Recognizing that we need 9" between each rail (our tallest binding was 4-1/2"), I lined up the rails 9" apart, adjusting the pencil marks.  Once I had a plan, I set the support back against the wall, held the rails up to see how it would feel.  Then, I pre-drilled the holes for the hinges (making one on each rail large enough for the eye-bolt) and assembled.  I also pre-drilled holes at the top and bottom for wall-mounting.

Installation
testing installation
Once the rack was put together, I wanted to see it in-place.  I discovered that the bottom rail was so low that I had to remove the eye-bolt so the hinge would open enough for me to access the mounting holes.  Hmm.. opportunity for model improvement.. I pre-drilled one hole in the wall and mounted the rack with a 1" sheet metal screw.  This held the rack in place so I could pre-drill the remaining holes without the rack slipping.
A test installation wouldn't be complete without filling it with snow equipment.  I put 2 boards (mine and T's) on the bottom rack, 2 sets of ski's (K's and C's) and Boo's set on the top rack.  K2 gets new-to-us ski's this year, so I left his off.  With the bungee's, the equipment sits well.  I will apply bathtub treads to help hold things in place, but it looks like the passengers will be comfortable and safe, and the equipment a-fixed.

That's it for today.  I still have some clean-up to do, but in just 4 hours this went from concept to installed.  We may use the racks as garage wall-mounts too.  Each one attaches with 4 screws.  Neat.  More next time, and thanks for following along-

Friday, March 2, 2007

AirCooled Aftermarket Axis of Evil

Yesterday's posting about the Weber Progressive Carb in the Wintertime reminded me of my AirCooled Aftermarket Axis of Evil. What is this Axis of Evil? Well, its not Korea, Iran and Iraq. It is a collection of modifications performed on aircooled vehicles that are all done together for some reason. It seems like there are 3 different things that all get changed around the same time by folks that mean well, but don't realize they're doing their air-cooled VW a disservice. Maybe they got misled by some flashy advertisement. Maybe they were talked into it by a mechanic that "used to race" so "he knew what he was doing". Regardless, if you find one of these aftermarket modifications, the odds are very good that the other 2 have been made as well. Bear in mind, if the VW engineers could have left off a bolt, they would have saved the company a big ol' pile o' cash after producing millions of these engines.
I'll spend my next 3 posts on each of the different AirCooled Aftermarket Axil of Evil modifications. After yesterday's post about the Weber 32/36 progressive, we'll logically start there. Its not the worst of the Axis of Evil, but its not part of the Coalition of the Willing either.

Evil Aftermarket Modification #1: Weber Progressive 32/36 Carb.
I know fellow bus drivers that swear by these carbs. Usually it comes up in a conversation about why they only drive their bus in the Summertime. "Busses can't be used all year 'round," they say. "They don't like the cold." Ahh yes... good old balmy Germany... that's where my bus wants to drive. That's crazy talk. If you don't like driving your bus in the cold because it doesn't have heat, say so, and I'll happily help you fix it. Your bus likes the cold fine. Your centermount progressive carb doesn't. It really isn't the carb's fault, though, its the fault of the long intake that the carb sits on. After the fuel and air mix together, it travels down 15" or more of pipe to the intake port on your head. That pipe is out there in the elements, not heated by anything, so the fuel mixture gets all dorked up and by the time it hits the combustion chamber it doesn't burn right. This carb was designed to sit right on top of the Pinto engine, getting warmed by the engine block. No such luck on theVW, especially the pancake motor in 1972-1983 bus/vans.

How do I recognize this evil?
When you pop the rear engine door and look inside, there will be a silver squarish thing sitting right in the middle of everything. If it is exactly as it comes out of the box, it will have a chrome aircleaner on it. It is sitting on long silver tubes that look like electical conduit. "Aw.. but it looks so pretty," you say. Yeah, pretty, but grossly inefficient when the air temperature drops below 70F or gets near the dew point. Here in the Pacific NorthWest, its a rare day when its not near the dew point except in the Summer..... which, oddly enough, is when the local Weber drivers think is the only time to drive a bus. Coincidence? No, they've been confused by the evil-doers.

How do I eradicate the evil-doer?
There are a few options for reducing the negatives of the Weber (containment of the evil-doer), or you could toss it completely for the correct induction system for your make/model/year.
Option 1: you could add insult to injury by trying the GM Cavalier trick. The Cavalier had a similar problem with its induction system, so GM added a heated gasket to warm the system. Whaddaya know, it fits between a Weber and that ridiculous electrical conduit intake. I have not personally done this, but I have heard that this does actually work, but you need some kind of thermal sensor to tell it to turn itself off. Sounded dangerous and little like like nonscience, so I tried...
Option 2: find a source of warm air and route it into the aircleaner. This helps the carb work better down to the mid 40F's, and drivable into the mid 30F's. I went into more detail in yesterday's post about this. The best solution is replacing the whole thing with what was removed in the first place - either dual carbs or fuel injection. These are more expensive options, but doing it right isn't usually the less expensive way in the short term. It is usually the less expensive way in the long term, though.

Dual carbs and fuel injection are not harder to dial-in than the Weber, nor are they harder to routinely maintain. What's hard is finding what's wrong with the used parts you have. Run a Weber for 30 years, and see if you don't have a similar "what's wrong with it" head-scratching session. The Dual carbs and fuel injection that came with the bus have 30 years of millions of owners experience to draw on. Removing the evil-doer in this case is easy; its the establishment of a stable system after the fact that's the challenge. That's usually because you're doing the work with the parts you have, not the parts you wish you could have. Hmm.. that sounded eerily familiar.....

Next time... Evil Aftermarket Modification #2

Thursday, March 1, 2007

Cold Weather and the Dreaded Weber

The Pacific NorthWest has been experiencing its last throes of Winter these last few weeks. Ever since Puxatawney Phil didn't see his shadow, it seems like the weather gods have decided to prove him wrong: there will be more winter. Here in the Pacific NorthWest, we've had "wintery mix" which means rain, freezing rain, sleet, hail and snow shifting from one to the other throughout the day. Did I mention gusting wind? Oi. It makes driving a little more exciting, but traffic a real bear.

When the air gets this cold, it takes a long time for Hapy to warm up. When I first bought Hapy, he was missing a number of pieces that helped to keep him warm - making his warmup never complete in winter. I'll go into those part identification and installation adventures another day. Even after finding and installing all those parts, though, the non-stock Weber Progressive 32/36 carburator would not perform well in the cold. If the air temp fell below 50F degrees, he would buck and toss like when I first learned how to drive a clutch. If you're having the same experience, I'd suggest you try this:

First, find a snorkelled air cleaner that fits the top of the Weber 32/36. I bought a "Sprint" air cleaner from Pierce Manifolds for $15. This fits perfectly on top, and bolts down with the filister bolts you use on the chrome air cleaner the Weber came with. This will allow you to control warm and cold air entering the carb.
But where does the warm air come from? Look at the right side of the firewall when looking in through the access hatch (top or rear). Is there a steel elbow that points up that's maybe 2 inches across? No? Is there a square hole with 2 bolt holes on either side of it? Yes? Ok, you're missing 2 key pieces of tin for getting the warm air into your carb. Now, if you have a fuel injection (FI) firewall, you may not have either of these items, so you may have more tin to replace. Honestly, if you have to go that far, you may want to consider returning to FI. Anyway, the pieces are on this diagram, numbers 42 and 43. Number 42 is the elbow on the inside of the firewall and #43 is a longer elbow that bends around the fuel pump (if you have a mechanical fuel pump) and to the firewall. I got these 2 pieces from my man Ken at theBusCo.
Getting these pieces to align without dropping the engine is a challenge, especially if you have a mechanical fuel pump, as the longer elbow needs to fit between the fuel pump and some of the engine tin. You do have a hole in the tin where the long elbow comes down, right? No? Ok, you have newer tin so you can either buy a "new" piece or cut your old one. I cut mine and I now regret it as I have to plug the hole to put FI back on. All of the pieces do fit together, and it can be done by yourself, but its much easier if you can get a friend or a willing child to hold the small elbow in place as you thread the filister bolt through and tighten it down. When its raining, and you're working in your driveway (as I was), you really appreciate hot tea afterwards... and a long shower.
After the tin is in place, and the snorkel is attached, you've finished the hard part. You need a flexible air hose to connect the small elbow near the firewall to the lower part of the snorkel. I got a standard sized one at the local GI Joes. Route the air hose under the long intake runners so its out of the way and any residual heat will warm the runners a little.

To make use of the new equipment, lift the flapper on the snorkel all the way. This will bring just the warmed air up into the carb. In Summer, lower and click-shut the flapper so only cool air enters the carb. This is important as in the Summer using only warm air can overheat your engine. Also, you get better power with cold air entering the carb, so you may want to play with where you set the flapper. You should find that by using the snorkel, you can drive your bus down into the 30F temps before you have the bucking return.

This Winter, especially these last few weeks, I have driven my bus in 35F temps uphill on the interstate. I have had to stay in the right-hand lane, but I've been able to stay on the road. Two years ago, that would not have been possible. If you're having troubles with your Weber and either can't afford to get FI ($250) or don't want the hassle of working on a FI powered engine, you can get the tin, snorkel and the hose for under $50 and a couple hours work. Just try to find a dry place to do the work.