Showing posts with label cut. Show all posts
Showing posts with label cut. Show all posts

Tuesday, December 15, 2020

Chasing the Hapy Electrical Gremlins (part 3)

Continuing on our journey through the darkness of the wiring rat's nest.
 
Shouldn't Have Cut That
not quite "before",
dashpod already pulled
I'll just jump right into the interesting part. Well, mostly. I started in the engine compartment and removed the wiring related to the coolant heater first: the relay box, the wires down to the glow plugs, etc. That much was great. Then, I moved on to looking at some of the wiring above, and as the bold-faced line implies, I cut something I would best not have.
 
Reflect back to the last time I clowned around on this wiring, I dug deep into the fuse-box. I started by pulling the fuses for circuits Hap doesn't need. Circuit by circuit, I cut that unnecessary wiring by referencing fuse sockets where the fuses had been pulled. That plan worked great. Lots of extra wiring got removed, and the engine still ran. I still had the sporadic not-limp-mode, and the occasional Hapy-don't-wanna-start issues, but they both seemed improved. Well, this time around, I got into the fusebox and saw a few wires that did not appear to have a partner on the other side of the fuse. So, I figured I just missed them the first time, and cut them. Well, that was wrong. Their "missing partner" was actually a common-line always-hot (circuit 30 in VW-speak) that was kind of hidden from view. Well, I didn't see them anyway. The wires I cut are for powering "engine control" circuits, of course. So, kinda important. Ugh.

Fuse Box Smaller
don't actually need
any of these relays
Once I realized that the wires I cut were critical, I needed a new plan. A while back, I bought a small relay box thing off eBay that has 6 relay slots and 6 fuse sockets. Once it arrived, I looked at how many fuses were in the donor fuse box and how many sockets were in that smaller box and the math did not add up. That was all before I did the clear out I mentioned above. After that, I was down to 7 fuses, and one of them was for the OBDII plug that I don't actually use. So, I think the fuse socket numbers may work. As for the relays, I only need 2 of the donor relays: the infamous 109 (main power) and old 180 (glow plugs). All the other ones can go, which leaves me 4 slots for other things, like the "RUN" and "START" trigger relays I have connecting the ignition from the front to the electrical from the donor. Neat. I didn't mean to change the fuse box and the relay plastic holder thing, but when I cut those two engine control wires the die was cast.

Label, Label, Cut
smarter way to remove
extra wiring
So, into the darkness we go. I started with the more obvious wires, like the thin little wires on the 180 (glow plug) relay. Then, I moved on to the T10 plugs. There are 5 (Blue, White, Black, Orange and Brown) 10-pin plugs in the mix of all that rat-nest. I unplugged them, and started dissecting by labeling either side of the cut, describing what is on the other side, and cutting. This picture on the right here explains the wire coming from the ignition switch position 86s as an example of how I dealt wit the wire-snarl.

While that sounds like quick work, I have moved slowly, researching each wire first, to make sure I don't have another "engine control" mishap. And, I want to do more than just label where it went; I want to know what it does first. This is a lot like a jigsaw puzzle where the more you do, the faster it goes until you eventually have all of the wires you intend to cut labelled and cut apart. I am almost done, which means the next post on wiring should include some building back up.

Diagramming
One last thing I have been doing, is crafting my own wiring diagram. I started by scanned the wiring diagram for the early ALH engine (80-pin ECU) from the Bentley. There are 13 pages. I am examining each circuit across the diagram and editing the image of the page to reflect what my circuitry will look like. I am retaining the original circuit numbering, etc. but adding the number of the fuse that I am using in the new fuse box to the documentation. Perhaps more importantly, I am erasing the wire references to things that I no longer have, like the coolant warming glow-plug stuff. My thinking is that this way someone who knows the original wiring (looking at you, Justin) can understand the diagram just as well as I do. This diagram will replace the diagrams in the 3-ring binder, since the 2 sets in there are both for later ALH models, so they are informative, but not exactly 100% representative. Between the cold and the dark, the diagramming effort helps me feel like I am moving forward while also creating clarity around the work.

My CoViD-19 Plea
I take a 2 mile walk pretty much every day to shake off the cabin fever and to get some exercise. Every day, I see 20-30 people also out taking walks, riding bikes or taking a run as well. That's great except I can count on one hand the number of people I encounter with a mask on at all (even worn wrong). The other day, I counted 3 people out of 28. Seriously. Our tiny state is consistently seeing over 1200 new cases a day, which is alarming when you consider our "summer peak" was 430 cases a day. Please keep your masks on, its not a political statement, it's not a chin-strap and it doesn't work unless it covers your nose and mouth. It's to protect others from you, not the other way around. We don't know if you have the virus or not, and quite frankly, if you're wandering around without a mask, and hanging around with others who don't have masks, then even if you had a test today... you don't know either. Just because you're outside doesn't mean you can run/walk/bike right past other people a-huffin and a-puffin (and sometimes a-coffin) without a mask. We are all tired of this, but that doesn't change anything about the importance of respecting it, and each other --

Tuesday, July 17, 2018

MGB - carpeting (part 2)

This is a continuation of the previous post about installing the carpets into the MGB. At this point, I've mapped all of the various pieces of carpet to where they go in the car and I've traced and then cut thick or thin insulation to go under the carpet for the respective sections. Now, it's time to play with spray epoxy.

Back to the Directions
For the install, I followed the directions for the order which carpet first, second, etc. For each piece of carpet, I had something to go under it (except the transmission tunnel). For each piece which directed gluing straight to steel, I would test fit the insulation, then test fit with insulation and carpet. If necessary, I would trim the insulation a little bit so it wasn't visible. Then, I'd spray epoxy onto the insulation and install it, holding it in-place for a 30-count or longer. Then, I'd test fit the carpet on top of the glued-down insulation, then epoxy it into place by spraying epoxy onto the carpet underside. Remember to let the epoxy set-up a little bit before slapping the things together. Wet won't hold; it needs to tack-up a little bit: spray the underside well away from the car, let it set up for 15-30 seconds and then apply in-place. If you, the reader, are looking at this for guidance, take care with the transmission tunnel carpet. I realized after mine was in that a shifter cover plate hadn't been put back in, so I needed to cut a small line in my carpet in front of the shifter to enable that re-install. Since it will live under a console, it doesn't really matter, but I really don't like cutting when I don't need to. Honestly, it is really hard to tell that the carpet was cut there now even without the console.

No Glue, But No Snaps
The carpets that sit on the floor under the persons in the car and the piece on the back deck are not glued in. Instead, they were held in place with snaps from the factory. Since I replaced my floors, many of the old snaps were gone. I had a decision to make: install the snaps or try something else. Knowing that the snaps had to be in exactly the right place for them to align with the snaps in the carpets, or there would be lumps in my brand new carpet, I decided to not install snaps. But, I needed something to hold the floor mat especially under the driver's feet. Otherwise, it could slide around under the pedals making for a dangerous driving condition. I found Velcro at Ace Hardware that was designed for wet conditions and it could hold up to 30 pounds. Since we just need to hold carpet, this felt like a good way to go. I cut sections out of the insulation, glued the Velcro to the underside of the carpet and corresponding spot on the floor. Now, the carpet holds in place, and retains it's original ability to be removed for cleaning and access to drain plugs. And no lumps.

Cutting Holes
In order to re-install seat belts and the seats, this brand new carpet needs to have holes cut into it. I found this a little hard to embrace at first. Since I was putting insulation under all of the various pieces, though, I could figure out exactly where the hole was supposed to go with something that wasn't carpet and then transfer that spot onto the carpet. This worked well for the sill carpets (that section from the ledge along the bottom of the door to the main floor) where the lower seat belt mount hole is, but greatly complicated an already difficult wheel arch. Fortunately, the transmission tunnel carpet had the holes pre-punched. This made aligning the carpet easier in that respect, but made the overall install of that carpet much more harrowing because everything had to line up perfectly.... with epoxy sprayed on it. Move quickly.

The last holes to put into the carpets are the holes for the bolts to hold the seat rails. In the MG, each seat is held in with 4 7/16" bolts. The carpets do not ship with the holes pre-punched, so you need to locate them yourself. Not all of these holes pop out the bottom; in fact, only one does. The front 2 pass into a cross-member and one of the rear ones does too, leaving just the one. I started with just the insulation down, and pushed a finish nail up through the one hole. This removed front-back and left-right sliding of the insulation while I located the other holes. These, I found in a more traditional way of folding back the insulation until I could locate the hole, and guestimated where it passed through the insulation. While some holes took more than one try, I located the holes with finish nails, leaving them in the insulation for transfer to the carpet. Taking the insulation to a table, I set the carpet on top of the insulation and pushed the finish nail through the carpet, marking the hole, and then put blue tape on top of the nail to hold the mark. With an exacto-blade, I cut a small "X" at each nail, testing the size with the seat-rail bolt so the hole was only as large as needed to be. With the bolts pushed through the holes in both the carpet and insulation, I could set the carpet in place and then put in the seats.

Seats In
Once the carpets were in, I put the seats back in. The seats were originally installed with a wood slat running under the steel rail to lift it up off the carpet a little bit. Not surprisingly, these wood slats were rotted away. Instead, I boosted the seat up off the carpet by putting a slightly over-sized nut under the seat rail where each of the bolts passed through to the floor: one per bolt. These 4 nuts created little stands for the seat rail so it sits just above the carpet. I expected this to be a challenge, between the low ceiling created by the convertible top, the small holes, getting a nut under the rail, juggling an old seat, etc, but it really wasn't. The blue tape gave me clear targets for the holes in the seat rails so I could get the seat in the right spot without the carpet moving. Then, one corner at a time, I lifted the rail, slid a nut under the rail and the the bolt through the rail, then the bolt and finally into the hole in the floor. I would lightly thread the bolt and then move on. I tightened the bolts snug as pair: front then rear.

Finishing
I finished out the rough-in by making a small cut in the transmission tunnel carpet and installing the shift plate. I followed my now-usual pattern of soaking the old plate in vinegar for a few days to get the rust off; then, cleaned primed and painted it. The install of the plate was simple: re-use the 3 Phillips screws at the front. I re-used the original shift boot after cleaning it up with some Meguiar's vinyl cleaner just to get the shifter together and looking fairly good. I'll be switching out the shifter boot with the rest of the interior panels and seat covers later. The boot is held down with a new black ring and chrome bolts. The ring and bolts were less than $10US, but that change greatly improved the finished look.

I installed new door rubber seals and the stamped-steel transoms (with new screws) to complete the effort. The ends of rubber seals are held in place with small chrome bits, and otherwise just press onto the lip which runs along the edge of the carpeted sills. The stamped-steel transoms are held on with 6 small screws, and after some polishing, look fairly decent for original pieces.

Now, it looks and sounds like a "real" car. When the doors are shut and windows up, the car purrs. When I stomp on the fast pedal, it has a little roar to it. I still need to put the center console in (for climate control) and it could use a radio, but the little car is about ready to be a daily driver.

Thanks, as always, for following along.

Thursday, February 26, 2015

Windscreen Removal

Well, the prep for painting has really gotten underway now. Today's brief post is about removing the windscreen and what lies beneath. Depending on your windscreen, you may be removing it to replace it. If that's the case, you may not need to take as much care as I did. My glass was perfect, but I needed to get a look at the metal surrounding it as well as get the paint underneath it. One more seal is worth the rust containment.

Cut
multiple passes
For tools, you only really need a box-cutter / X-Acto. Extend the blade halfway. Approach the bus from the front and go to the top corner of the passenger side first. Slide the side of the knife blade against the windscreen with the sharp side pointing down. Cut the rubber seal from top to bottom by sliding the side of the blade against the windscreen. It will resist, so that's why we're only using half of the blade edge. Don't press too hard; let the knife to the work. The harder you fight it, the more likely you will scratch your windscreen. Extend the blade to 3/4 length and run the same seal edge top to bottom. Extend the blade to full length and repeat. This time, you should hear that satisfying noise of the knife against the A-pillar. The rubber should separate from the glass and just hang there. If not, gently run the knife along the A-pillar being careful not to disturb the paint. It is possible a previous owner painted the seal on, ran caulk to try to stop a leak or glued it in. Glue is not necessary for this seal. Nor is caulk, but I've seen some crazy road-side repairs go untouched for years, and caulk is definitely one of them.

Repeat
Repeat the cuts for the driver side and then the top. By now, there should be rubber hanging off the bus, or sitting in strips by your feet. Nicely done. If its an old seal, some of those cuts were very difficult. If it was anything like my first seal replacement on my bus, there were a few spots where I was able to cut right through very easily. I discovered that those spots also aligned with rust. When I cut off the seal the other day, it was only a few years old, and held very well. I'll be getting another Bus-Depot seal for the re-install later.

Bottom Cut Last
Pulled away a little bit
The best is saved for last. When I did my first seal, I had to be careful while I cut the last section. It wasn't holding very well, so I had to keep one hand holding the windscreen while I finished the cut. The newer seal, though, held strong even after I cut off the bottom. The windscreen held to the bus. It held very firm, actually. Your experience may differ, and you may want a buddy around when you make your last cut (as I did a few years ago).

Pop It Out
Old seals don't hold well, so the windscreen may just fall out once you've made your last cut. In my case, I reached one hand through the front door and pushed towards the front while catching the edge out front. This freed the sides, but the center still held. I had to grip the windscreen from the bottom near first the driver side then the passenger side and gently pull forward. Slowly, the seal gave in and handed me my windscreen. I carefully set it where it wouldn't get scratched and pulled out the remains of the seal. If yours was glued in, this could take some time. You want to get back down to smooth metal.

Now What?
glass out. rust inspection
I looked at the rust treatment I did years ago with some POR15. I was impressed. From my memory, the rust had not meaningfully advanced. Still, I needed to sand the whole opening to make sure. It looked pretty good, so I decided I would just expose the rust (read: sand and Dremel) and re-treat it. Then, I'll just handle it like any other metal panel: prime and paint with lots of sanding mixed in. Since it lives under a seal, there's no point in adding Bondo to the rust pits except as practice for visible spots I need to do later. Still, I'm going to skip Bondo'ing here.

As always seems to happen, this small painting effort has grown into a pretty big deal. Next up, removing the dash-top, more rust inspecting and sanding. Apart from deciding how far to go with paint on the interior, I think I'm almost done with the initial prep work. I still have lots of sanding and such to do, though. Unfortunately, that doesn't lend itself to print very well, so it might be a little while before my next few posts appear after this. Thanks for following along.

Sunday, November 30, 2008

its in the hole!

In March of 2007, I had a post about gaining access to the engine in a 1972 VW bus. I outlined the 3 different sizes of standard openings that VW offered in their aircooled bus (and the type 3/4). After a year and a half, and a decision to swap a diesel engine into Hapy, I've put topside access into my 1972 bus. I didn't come to this decision easily (nor quickly, obviously), but now that its there, its incredible. Even if it is just a hole.

Measure, and then re-measure for good measure.
In the link above, I provided 3 possible stock-ish sizes. I liked the access idea from the typ3/4, so I took those dimensions, and made it a little smaller at 20" deep and 30" across. The hole can be expanded, if the type3/4 cover/lid becomes available. That's a decision for another day. As it is, the right side (facing front) is butted up against the support rail that runs front-to back on the right side. The front side runs along the firewall.

mark it, tape it, mark it again.
Centering the 30" on the latch, draw the lines with a T-square. 16" from center to the right is the support beam, but 15" off leaves just enough space to fit a 1" square tube in the future. 20" from the firewall leaves about 4 inches from the latch (see the picture to the right here). I'll need to weld in a support there along the backside later. Anyway, with a T-Square mark the rectangle with a pencil, over-shooting the intersections. Double check the lengths and the squared corners. Take masking tape and tape over the lines, centering the tape on the pencil lines. The tape will help keep the cuts smooth. Re-mark the lines with a sharpie so you can see them when you're working the grinder.

cut with care.
Break out your angle grinder with a cutting wheel. I bought a 4 1/2" for this job and got a DeWalt cutting wheel. Start near a corner and work one line. Stop before you get to the end and switch to another line. I did the left side then the front, then right and finally the rear. This order allowed me to climb into the bus to cut the front without stressing it. Once the lines were done, I went in through the back and finished the cross-support bar off. Finally, complete the corners, and the hole is finished.

enjoy.
The resulting hole needs to be filed or otherwise protected, or you'll cut yourself up on it. I'm putting that off for now. Same goes to creating a hatch. I didn't realize just how much better it was until I got back to putting the engine in and was able to see the whole thing. As it got dark, I set up a cliplight from the rear door support and it was incredible. Imagine crawling through your front grill to work on your engine for 4 years and then to finally have a hood. Wow.