Showing posts with label sensor. Show all posts
Showing posts with label sensor. Show all posts

Thursday, August 20, 2026

Catching Up on Cars

It has been a busy Summer of car stuff. Some wrenching, some otherwise. In today's post, I will not try to cover everything, but there has been a lot. 
 
Oliver freshly cleaned
Before I begin, you may have noticed a new sticker on the right-hand side called "Electoral-Vote". If you aren't familiar, that is a site run by 2 history professors who started a site initially, I think, to analyze polls. I have been reading their page for well over a decade; maybe 2 decades at this point. From humble beginnings that aimed to provide insights into political polls, they are a daily site that examines the (mostly) US political theater. As the national political disposition has shifted right-ward, their political position has remained around or just left of where the political middle was during the Bush years. Now, that position is left-of-center (because, again, of the national shift) in the continuum of US national politics. As the primary season has ended, they are returning to their roots, looking at polls and providing the kinds of insights only 2 life-time history and statistic's nerds could provide. If you find that stuff interesting, check them out. Neither they nor I get anything money-wise out of my putting that sticker on my blog. They get clicks, I literally get nothing. Back to cars.
 
K'Lack
P0726 re-appearing
We will start with my nemesis car: K'Lack, the 2004 Jetta TDI Wagon that previously belonged to our son K. After driving it for years and logging thousands of miles, he needed to sell it off and get something that was newer? broke down less often? I'm not really sure, but at the end he was having transmission issues. Regardless, the trade-in amount he was offered was pennies-to-dollar value. So, we bought it for Kelley Blue Book value at the time (around $4500US) and took it directly to a transmission shop who was qualified to do transmission work on these 2000's-era automatic transmissions appearing in VW's and Audi's. Through the benefits of successful aging and poor record-keeping, I don't remember how much we paid them to rebuild the transmission, but it took literally months. If I remember correctly, it went into the shop in December and we got it back in March. It was around this time that our niece (another K, so I think maybe since all these "kids" are adults now, maybe I'll just start using their names), Krista needed a car. Her former car failed in some way I don't remember. We intended to sell her Flash. Remember Flash? He was a great 2001 VW Jetta TDI sedan, but he had a manual transmission. Loved that car, but a different niece needed a car, so when Krista was unable to drive a stick, Flash went to the other niece and K'Lack went to Krista.
 
replacing K'Lack rear caliper
Now, years later, and many repairs ranging from replacing the oil pan to a timing belt and camshaft replacement, K'Lack is currently having issues I cannot track down. It is throwing a P0726 code and after tracing wires and replacing the crankshaft position sensor, the issue persists. The code means a check-engine-light is lit which means the car will not pass emissions. It is also virtually un-driveable. It barely starts and at any point during a drive the car may suddenly shift into a too-low gear, causing it to buck. It is quite alarming and dangerous. I have date with a mobile mechanic, Ian, who has helped on some of Cedar's (that's "C" in all prior posts) cars. I hope very much that we can resolve this and get Krista back on the road with K'Lack. In the meantime, it is parked under a plum tree in the back near the shop and Krista is driving Boo's (okay, her name is Angela and I'll refer to her as Ang from now on) Ang's Astra.
 
Oliver
In the interest of getting Oliver, the 1978 MGB, out of the shop so I could move things onto shelves, I got Oliver running well enough to back out and idle-drive under a tree. I say idle-drive because the throttle cable had seized. Fortunately, parts for an old MG are not nearly as expensive as parts for new cars, so a after few bucks and about 15 minutes, the throttle cable was replaced, and Oliver could start and move around. Thrilled, I drove him out to the front and gave him a long overdue bath. His brakes were still a little squishy, so I moved him to the other side of that plum tree in the back and put his cover back on. I have to do a system-wide look at the brakes. They have been acting like they needed a bleed for a long time, no matter how much I bleed them. I think I must have a loose fitting somewhere that lets air in. I still intend to get him out and around, even with squishy brakes, before the Summer is over.
  
Hapy
cursed outlet flange
Earlier this year, I got Hapy put back together. I drove him out to Sheridan where Justin could do the injection pump re-seal. On the drive home, I popped the boosted air pipe and sorta limped home. But, after that, I took him on around-town outings and he ran great. He would start right up, have lots of pep, moved through the gears well. For almost all of the month of July, he was set up festival-style in the back, providing music, a hang-out spot and a groovy vibe. This past weekend, Ang and I had 2 different events. First, we had tickets to Joe Russo's Almost Dead (JRAD) in Eugene. JRAD brings the energy of the early 1970's versions of the Grateful Dead while performing everything and anything across their song catalog. I highly recommend to my DeadHead friends. The next day, I had an early-afternoon show in Rockway Beach, playing the NCAM benefit festival. I'll post on the festival later, but our adventure started and ended Thursday night, heading south to Eugene.
 
As I've mentioned before, Ang and I like to leave for events the night before, getting as far as we can in the cool dark and then vagabonding (boon-docking to some) in a random parking lot or on the side of the road to catch a sleep before completing the journey in the morning. Hapy likes the cool air and we really like awakening that morning most, or all, of the way there. The drive was relatively uneventful until after we got south of Wilsonville. I noticed that the rear window was getting blurry, and I had just washed it when we filled up. Growing concerned, I pulled off into the Charbonneau rest area near Aurora and glided into a parking spot. I went around back, opened the rear engine hatch and could see that the coolant bottle was empty, and I could hear steam. After moving the bedding out of the way, I could get the top hatch open and could see that the coolant was escaping from the cursed coolant outlet flange. I would later discover that the c-clip or "U" clip that holds the coolant sensor in place had a broken leg (so, really a "J-clip). If you look at the picture on the right, there ought to be a little plastic tab thing sticking downward from the bottom of that dark channel on the right side of the outlet flange. That would be the end of the "U" that's not there. Our trip to Eugene was over and I called for a tow.
 
trench filled
We waited for about an hour, and the truck operator seemed fine enough. He was nice, albeit quiet. In retrospect, he seemed less comfortable with Hapy not having a parking brake but Hapy has been on a flatbed lots of times without an issue. Until this time. I believe he did not strap the wheels down as tightly as prior truck operators had. I say that because Hapy seemed to move front-to back a little bit as he backed the truck into the driveway. I had not noticed that when he was loaded onto the flat bed in the parking lot. We rolled Hapy into place, and Ang and I called it a day, returning to Hapy the next day... when we discovered that putting Hapy in gear was not enough to hold him in place. Since it was enough to hold him in place on the flatbed, at least while he was getting strapped in, and this was over an hour after we had overheated, I conclude that the tow somehow messed up the transmission-to-engine connection (read: clutch). I wanted to see if the engine was locked up, so I put a 19mm socket on the crank end-bolt and gave the engine a short turn (like 15*). The timing belt moved, the camshaft moved with it, so I concluded no major engine damage was done. Or, at least, it's not frozen in place. That's huge, but I think I will need to pull the engine and transmission apart to fix whatever went wrong in between. With this knowledge, we called it a day on Friday and spent a lovely day at the beach on Saturday.
 
trench filled
Since I still had a trench running the length of the lane-way, I spent Sunday morning filling the trench. By the end of the day, Ang and I had flat-towed Hapy back to the shop with the X-Runner and 20' of trucker's chain, parking him out front. I need to clear some space inside the shop to put him, and get him in there. Then, I have the equivalent of a clutch job ahead. The last time I had to remove, separate, re-acquaint and re-install the engine and transmission, I vowed that I would cut a rear apron into the back so I could just remove the engine. Looks like that time is now. Regardless, Hapy will probably not make it back out on the streets this summer. Could I get it done before Summer ends? Maybe, but we have lots of things going on and I don't know if I have a weekend to dedicate to that right now. Besides, if I am going to cut, I want it well planned with a means of fastening what I have removed before I pick up an angle grinder.
 
EDIT: I was trolling through some of my old posts yesterday when I came upon Front is Front which clearly describes this same coolant sensor leak recurring, until I put the clip in from below. Over 15 years later, and I'm repeating myself. Had I remembered, or read, we would not have lost coolant, broken down, etc. There's a lesson in there somewhere.
 
Wrap
With Hapy's catastrophic failure, we are down to one operable car: The Toyota X-Runner, which Ang drives to work. She has a lingering bad shoulder from a skiing crash a dozen years ago, so driving a 6-speed in rush-hour traffic is really taking a toll. If Ian and I can't get K'Lack fixed, we are going to need to re-po the Astra and have Krista solve her car need another way. Generosity reaches a limit when another's convenience is literally causing you pain.
 
Well, that's where those 3 cars are at. I have a long tale of 2 Astra's to share another time. We have lots of active construction Ang and I are doing with our friend Ray, so I'll update on that, the Astra's and whatever else happens around here as things roll. I hope the reference to the electoral vote guys doesn't cross some no-politics line for you. I generally don't bring that noise in here, but elections are coming, and we all need to be as well informed as we can be.
 
Thanks as always, for following along. Until next time-

Wednesday, April 22, 2026

Hapy not Spittin Fuel

I managed to get Hapy, the 1972 TDI-powered microbus, over to Justin to get the injection pump re-sealed this weekend. Today's post covers that adventure as well as a quick trip thru a K'Lack (2004 VW Jetta Wagon) issue.
 
Getting There
head seal complete
It has been 2 years since Hapy really went much of anywhere. Most of that time, he sat waiting for attention either in an unknown, but unstartable state or in pieces. Once I had him re-assembled with a new flywheel/ring gear and had a test drive, the original reason for him to have starting problems re-appeared: Injection Pump losing prime. I was able to prime the pump with a MityVac and then crack the injectors to get him running. And, in that way I took him on a short test drive, found some issues with the lights, etc. There remained many other issues, but at least I could get him running, stopping and had my lights so I could drive him an hour and 20 minutes to Justin's shop.
 
The night before our start-of-day appointment, I got Hapy out of the back and filled with B-20 biodiesel ($6.40/gal. same as dinoDiesel. Thanks, Trump). That morning, I filled up with coffee and hit the road. Most of the drive from West Beaverton to Justin's shop is on back country roads with few other drivers on an early Saturday morning and even fewer traffic lights. It was in the 50's (F low-teens C) and clear, making the drive very pleasant. At some point after I fixed the rear speakers, the stereo lost access to 12V so I drove in silence, a familiar scene for Hapy. The road was so easy, the thermostat never opened. I had the cabin heat on, so I may have been pulling just enough heat off the engine to keep the thermostat closed. Based on the UltraGauge, the engine temp was hovering around 180*F so running "cold". When I pulled into town off the country roads, I had a few cases of not finding 2nd gear. I noted that for followup later. When I arrived, Justin and I hung out for a bit before getting started. He has so many interesting projects all going at once, you have to absorb it all. I mean, who puts a TDI in an Audi TT while also putting one into a Rabbit pickup? Love that! The way he scraps discards and re-uses them for the basis of tools is pretty awesome too. He's even teaching himself TIG welding. Small crush, maybe. Okay, fine. He does do some impressive stuff.
 
Injection Pump (IP) Reseal
hammer mod perfecting IQ
Justin had encouraged me to get the seal kit from Cascade German, since they are local-to-Oregon, when we first set the apointment. I had already purchased the deluxe kit from DieselGeek. I didn't understand the difference. These 2 kits definitely vary in their intended purpose, so they have some meaningful differences. The Cascade German version is actually less expensive, but it includes all of the little seals usually replaced when a legit shop does the re-seal. The DieselGeek kit has far fewer seals (just the 2 on top and the head-to-base seal) and it is designed for the home-mechanic to re-seal the pump in their garage without removing the pump from the vehicle. The DieselGeek deluxe kit is more expensive because it includes specialty bits a car owner probably does not have, but are needed for the job. This differentiation is important and your case may lead you to the larger kit even if you do not intend to replace much more than the 3 included in the DieselGeek deluxe.
 
Once Justin discovered the gap, we made-do with the smaller kit. Justin replaced the top 2 seals first and then moved onto the head-to-base seal. Rather than use the included "retraction limiting bolt" and try to fit the new head seal over the top of it, the head was removed, and I held the guts of the pump in-place while Justin cleaned all the surfaces and installed the new seal onto the head. Once installed, he hooked up the VagCom and hammer-mod'd (link to Hammer Mod thread on TDIClub) the injection quantity (IQ). Justin was aiming for 6.0 mg/stk because the engine was cold (54*C).
 
The engine bay was pretty dirty, so lots of time was spent getting the IP clean before we began as well as afterwards when the whole engine got a cleaning. After it dried off a bit, we let the engine idle and we looked for leaks. None found. Justin did ask about how the starter was mating to the flywheel. It does sound loud, like it may not be meshing quite right. I'll need to remove and reinstall the starter and the starter adapter to see if I can get things to sit right. The original adapter and starter that I put in just worked for years. I would expect the new-also-stock starter would fit the same. Since this is a new adapter, that is actually designed for the application, versus one I dremel'd to fit, I would think it would fit better. It's a puzzler, but one I will consider carefully as I remove/reinstall (R&R) the starter to get it to hit the ring gear more cleanly.
 
Getting Home
If there is anything we have learned over the years about Hapy, its that he loves going places and really does not like going home. How many times have I left home and the road trip to 4 Peaks or some camping spot went great and the drive home was either very challenging or partially performed by a flatbed? Too many. This trip was no different. At first, Hapy ran great. The engine was responsive and stayed cool. Somewhere around McMinnville a charged air pipe popped off, leaving me running naturally aspirated the rest of the drive home. This served as yet another reminder to never leave home with Hapy without some tools. While the turbo is great for the overall power-band, its absence is really noticeable when trying to leave the line and get up to traffic speed. Now that it was about noon on an absolutely stunner of a day, the roads were busy where they had been empty a few hours before.
 
By the time I was approaching the Dundee Bypass, I was having increasing difficulty finding 1st and 2nd gear. Sometimes, one or the other would be right there. Other times, it was a "can't find it, grind it" experience. This persisted all the way home, forcing me to sometimes leave a stop line in 3rd. When you add in the no-turbo, I had some dissatisfied fellow travelers around me. I did get home, however, and I drove Hapy all the way into the shop so I can chase these issues.

K'Lack
After having something to eat, I switched over to K'Lack, the 2004 TDI Jetta Wagon with a BEW motor. It had been throwing a crank position sensor error, lighting up the check engine light (CEL), preventing it from passing smog. I had ordered a replacement from Cascade on Thursday, and it was in the morning mail on Saturday when I got home from Justin's. The removal/replacement of these is not complicated (remove bolt, unplug from harness, install is reverse), but getting to the sensor and the weird bolt head complicate things. The sensor sits right behind the oil filter on the front, when the engine installed transverse like normal. The bolt head is a 9mm 12-point. Half of my sockets are 6-point and the other half are 12's, designed, I think, for easier application onto hex bolts. In this weird case, that socket set perfectly onto the 12-point bolt head. With the right socket, short extension and ratchet the bolt comes out fairly easily. The plug end is fitted into a metal tang, but otherwise once unplugged, the whole thing can just get dropped through the gaps onto the ground.
 
To install, I plugged it in first and then covered the sensor with a rubber glove to lower it past the engine ick and then below the car. Could I have cleaned the engine bay before starting? Yes. But then I would have been lying in mud since the car was on my front lawn, not back in the shop and I didn't want to lay in a puddle. At this point, I found having another person to be your eyes is very helpful. I got under the car, un-gloved and suspended sensor in hand and had Boo tell me east-west, up down until I was able to send the sensor into the hole. By doing it in this order, the sensor wanted to be oriented such that the bolt holes lined up naturally. I sent the bolt thru, tightened with the socket/ratchet combo and I was done. Since I cleared the code we need to run a few cycles until it is ready to smog.
 
For the legal-minded, Oregon cops are interested in registration violations after years of looking the other way post-CoViD. K'Lack got a registration-violation ticket while legally parked in downtown Portland. Drivers beware.
 
Hapy Wrenching
Feeling confident, I switched back to Hapy, and re-connected the charged air hose. As I suspected, it was one of the rubber-to-metal bits. I cleaned both the outside of the metal pipe and the inside of the rubber with brake cleaner so they were more apt to stay together and then tightened the clamp down.
 
I next wanted to chase why the lower gears were sporadically missing. I checked the front of the transaxle to see if it was out of position at all. Nope. Right before Boo and I bought this house, I bought a Gene Berg shifter. The new-at-that-time seats were higher than stock, moving the approximately-stock-length Scat gear shift further away. The Gene Berg shifter is a few inches longer, so I figured there would be less leaning. I had not gotten to installing it before the house was bought and life took a turn. Anyway, at this point I looked at the Scat shifter I had installed, probably over 15 years ago and slid the vinyl boot up the shifter. The plastic bits on either side of the shifter appeared to be allowing more play than I remembered. Hmm. Then, I looked at the rest of that mechanism. It was very rusty, especially the foot that rests on the floor. I shot the bolts with Kroil and after waiting a couple of minutes, removed them with a 13mm spanner/socket combination.
 
rust under shifter
The floor under the shifter had meaningful rust to match the rust on the shifter foot. I don't know how much play was created by the plastic bits, nor how much may have been introduced by the rust. I do recall, however, that the Scat shifter instructions did not account for adjusting the placement of the shifter front/back nor left/right. When looking at the foot profile, it looks very much like it is designed to sit squarely in the oval without any adjustment at all. I don't know if this was a terribly good design, but I will be installing the Gene Berg shifter which does allow for adjusting. I cleaned up the rust dust, shot the floor and the shift-rod end with brake cleaner and got everything as clean as I could. Then, I painted the area with Eastwood's Rust Encapsulater (the new stuff is even better than the original) and called it a day. I still need to treat from below. I shot the picture on the right here as I was almost done applying the paint.
 
Wrap
Well, that's where we stand right now. I have been in and out of the shop a few times since Saturday and there is not a single drop of fuel on the floor under Hapy. So, we can close the book on the IP leak. I intend to complete the shifter swap and then R&R the starter next. I hope that will be the end of both issues, but I suspect there will be more to do than that. Then, of course, there are all the other things like a fuel level gauge, the radio, and the diesel heater just off the top of my head. There are many incomplete items on Hapy. Now that I have a mostly-inside (one doorway remains), concrete floor'd space to work, my desire to work on these cars has really kicked into a new level.
 
Thanks, as always, for following along and more next time-

Tuesday, February 3, 2026

Hapy Gets a FrostHeater

Today, I nearly complete the re-assembly from the flywheel (well, ring gear, really) replacement that has been an open effort since US Independence Day. I had to order a clip to hold the coolant temperature sensor in the coolant outlet flange, so this post picks up where I left off after placing that order. Before I begin, hapy belated GroundHogs Day or Imbolc, if you're a little less western in your seasonal outlook. Either way, there's 6 more weeks of winter because Spring Equinox is still 6 weeks away no matter what a Pennsylvania rodent sees. Anyway...
 
Some History 
installed
For background, Hapy was having increasing trouble starting over the past 2 years. I thought I was getting poorly manufactured starters because every time I replaced one, he would be okay to start for a few times. That was until the last couple, including a new highly-recommended starter from IDParts and a fresh local rebuild of the original TDI starter by a very reputable rebuilder. I concluded the teeth on the "ring gear" or in my case the teeth on the flywheel since this flywheel was one formed unit, had broken off enough that the starter teeth could not engage. This started a path that started with removing the engine-transaxle on my falling-into-pieces driveway, having the transaxle fall off a jack and popping off a flange, hauling Hapy in a sketchy way back to the shop, and finally, now, almost completely reassembled. When this saga completes, he would have been not running since July of 2024 (when we drove home from the final 4Peaks Music Festival).
 
FrostHeater
Frostheater is a vendor who uses a widely available Zerostart 3309040 coolant heater with hoses and brackets for a custom fit for various makes and models. If you have not tried one and are tired of cycling your glow-plugs multiple times before you can start your diesel in the winter, I suggest giving them a look. The unit Frostheater uses looks to be the top of the line from Zerostart in terms of build, capacity and cost. There are plastic other brands, and block heaters that are effectively a glue-on heating pad, but I have found these FrostHeaters to be really effective. From what I can tell, there are no moving parts. By placing the unit near the lowest point of the oil cooler loop the unit draws colder coolant from the oil cooler and the warmed coolant flows up through the upper bib into the head. That rising heated coolant then puts pressure on the coolant in the block to move into that vacuum, through the oil cooler and the loop completes. A few years ago, I installed a Frostheater into a 2004 VW Jetta Wagon (K'Lack). It worked great. We sold K'Lack to our niece a few months later, and she never used the heater. So, when we had to do a major timing belt and cam shaft maintenance, OldPoopie removed the FrostHeater, and restored the original coolant line which I left in place when I installed the Frostheater. The Frostheater and related hoses went into a box for future Hapy consideration.
 
Coolant Temperature Sensor
#6 in diagram
Before I get too far ahead of the story, I installed the coolant temperature sensor and retaining clip first. That sentence is easy to type, but the actual install is very unpleasant. In Hapy, the coolant outlet flange sits behind the fuel tank and barely above the top of the body cross-support that also contains the center-mount for the transaxle. So, there is no way to insert the clip from below, it must go in from above. Directly above the insertion point for the temperature sensor, however, is the to-the-heater side of the coolant outlet flange, leaving a 1/4" or so to fit the clip. Since the orientation of the clip is straight  up and down, there is not enough room to simply slide it in. Of course, let's not forget that you can't actually see anything because it is all on the front side of the engine. For the ALH-TDI engine install into the bay-window bus, I believe this is the single issue that challenges the install. It is minor, in the grand scheme, but it is still highly unpleasant when you need to replace this sensor.
 
So, how do we do this? With a fingernail, I find the slot on the far side (front) of the flange where the one side of the clip will go, and send one "leg" of the clip into that slot while holding the sensor firmly in place. The clip will flex hard, and the inner "leg" of the clip needs to bend somewhere while the first notch of the clip is slid in, I found that having it flex away from the flange (towards the sensor) gave me something to work with. Once the clip is most of the way down and it seems like the clip can't possibly flex any more, push the flexed inner "leg" towards the flange until it clicks into the hidden slot. I spent a couple of hours wrestling with this, and broke a clip along the way, but this method does work. These clips are inexpensive, so buy several when you need to install one. Also, I found it much easier to access the coolant flange from the driver side (the sensor side) if the charged air hose is removed.
 
FrostHeater Install
where fits FrostHeater
I could have stayed on target at this point, filled the system with coolant and started test firing the engine. In fact, I try to follow that pattern more recently: finish what you started, then do the next thing. In this case, I had already lost the coolant from just below the outlet flange and above. I figured swapping out one hose for 2 with the coolant heater was not a significant scope increase when compared to the effort to open the system to add the heater later. I figured adding it later could be years away.
 
All of the install drawings and instructions I was able to find gave very model-specific directions. I was able to determine through loosely related searches that the life of the heater is significantly extended if it does not suffer the constant vibration of being attached to the engine block. So, I looked for a place along the right side of the engine bay where it would be low enough to be nearly the lowest point relative to the engine block while still being reachable by the hoses I had on-hand. That area has a small wire bundle, the main 12V line and the diesel fuel lines, so my placement will need to be careful, but there is a section a few inches front-to-back where it could go. With that general placement decided, I shifted to hoses.
 
The BEW TDI hoses that were part of the FrostHeater kit are not an exact fit for my early ALH TDI. The top hose (red line in the drawing on the right), which runs from the top of the heater into the head hose bib which protrudes on the oil cooler side of the engine just below the coolant outlet flange (#11 in drawing), had an extra bend at the far end that I trimmed off. I felt that the extra bend made the hose want to have a large arc which would have created a hard-to-manage air pocket -or- it was a kinking risk, reducing the coolant flow. The lower hose that runs from the lower bib on the oil cooler to the lower bib on the heater simply would not work for where I could install the heater and still use the upper hose. So, I decided to reuse the hose I had originally running from the oil cooler to the head for the lower hose from oil cooler to heater (blue line in drawing).
 
viewed thru top hatch
Now, we get to hard-mounting the heater to the engine bay. The BEW install bracket on top of the heater unit was oriented to mount to the left side of something. I don't remember what. But the bracket could be easily removed with a 7/16" socket and flipped over, aligning the bracket for a right-side install. Flipping the bracket also placed the heater about an inch lower and set the angle of the bracket against the lip of the engine bay, offering some additional support. With the hoses attached, the heater unit had a smaller range of motion for deciding where to mount it without putting stress on the hoses. Still, I was able to find a spot where the bundle of wires and everything else would not get bound beneath the bracket, and marked it with a sharpie. I planned for and then drilled for a M6 rivnut. The M6 was considerably smaller than the original, but the heater is super light and I was fairly sure that bolt was designed to go into a pre-existing hole. I say "planned for" because once I got the hole drilled, there was no way I was going to be able to fit the hand-riveter into the engine bay and set the rivnut. So, instead, I simply sent the bolt through and nutted from behind like most things. It is still a M6 bolt, using washers, of course, just no fancy riv-nut. So, to remove, I will need 2 wrenches rather than one. Not a big deal.
 
Fill 'er Up
from behind approx level
With the cooling system seemingly buttoned up, it was time to add coolant and burp out the air bubbles. This is where my effort ran out of supplies: no G40 coolant on hand. I added some water to confirm there were no leaks, and after shifting the upper hose clamp on the FrostHeater, there were not any. In the picture on the right, here, you can see how well tucked up and out of the way it is, even though it is below the oil cooler. Note the dry, albeit stained, concrete floor underneath. No leaks.
 
I still need to solve for the routing of the electrical cord so it can be reached relatively easily on a cold day, but far enough out of the way that it is not subjected to flying gravel and road debris. At this point, I am looking at tucking it up behind the right rear wheel, under the battery tray and holding it in place with a strip of cable-management Velcro.It might be time to consider mud flaps back there to help protect the cable from tire kick up.
 
Last, when I removed the exhaust at the start of this project, it came apart where the pipe meets the muffler. To be honest, I was never terribly pleased with the exhaust that was put on there. But, it did last 15 years, so I can't complain too much. Still, I have a 2" exhaust kit that is a bunch of straights and turns that I intend to eventually cobble together into a better exhaust. I think, to get Hapy on the road, I will put the existing, falling apart system back in. Then, I can plan for the 2" exhaust as a near-future improvement.
 
Thanks, as always, for following along, and I intend to get coolant this week and get Hapy running next weekend.  
 

Tuesday, July 26, 2022

Nemo Time

Remember Nemo? He's the 1997 Audi A4 (B5 body style) that T bought and wrestled with for a few years, replacing the clutch and brake master cylinders as well as the clutch slave cylinder and repairing so many other things. I also did a TON on this car (just what I posted on), so the fact that he needed more was a little, well... frustrating. When T moved to LA, he signed Nemo over to me, and then we thought we had sold it within the family, after replacing the driver-side rear axle and wheel bearing. Only to have the power steering fail... ending that transfer. So, Nemo has sat in my driveway. He has many little issues: a water leak into the driver's footwell, a broken front passenger window regulator, a big hole in the exhaust, a sunroof that won't open, some other little missing bits, and, of course, the failed power steering. Today's post covers my efforts to resolve enough of these items so he can be registered and driven again.

Before I begin, the sanding on Zed continues. I will post an update next week, hopefully, with some meaningful progress. In the meantime, I have slowly crawled along with Nemo over the last few weeks, so I thought an update was in order.

Water Leak
Schmidty sniffing the ECU box
I believe I solved the water leak when I discovered that the plastic box that holds the ECU was not entirely attached. There is an obvious nut on the outside, near the driver fender. There is a second nut inside the box closer to the engine, back near the fire wall. Underneath the ECU, is a large (like 1 inch by 3 inch) rectangle opening into the footwell. This hole has a gasket, but if the box is not held down firmly enough to engage the gasket, water which finds its way under the box (which is a for-sure here in rainy PacNW) will run straight into the driver footwell. In Nemo's case, the inner nut was simply not there. I found one, and snugged it down. Problem solved. I hope.

Accessing the Exhaust
big old rusty dirty cat
The big hole in the exhaust has been a major pain to solve. The aftermarket cat-back exhaust installed by a prior owner did not have any support between the end of the header and the rear axle. It did, however, have a section of flex-pipe immediately after the header, creating the car's lowest point. So, when the car drove over speed bumps or dramatic driveway transitions, it was the flex-pipe which hit the ground. Eventually, that flex-pipe failed. With the failure came a Check-Engine-Light (CEL) preventing a DEQ pass. To resolve, I removed the catalytic converter, downpipe and mid-pipe so I could replace the failed flex-pipe. This removal is challenged by the usual issues with exhaust hardware, but the Audi has additional things, like heat shields, in the way. So, the air box needs to come out, and the passenger front wheel comes off so you can access everything. Even then, Audi engineers seem to like to use different fastener types and sizes pretty much everywhere. Of course, the owner plays a role here too.

Cat Away
cat out
After trying a wide array of tools, I ultimately needed a hacksaw blade to cut through the rusted bolts between the catalytic converter and the down pipe. The PO had used regular steel fasteners to attach them, and even after multiple days of spraying Kroil on them, they were rusted tight. I cut the bolts, sending the hacksaw blade between the opposing flanges, at least far enough for the bolts to snap in half when I applied torque to one end with a socket-wrench. This took some time and patience, and because of how the bolts are oriented in the engine compartment, I was only able to sever 2 of them. This loosened the connection enough for the downpipe to rotate on that last bolt, allowing me to pull the 2 out the top of the engine as a unit. I cut the other bolt off, separating the 2 pieces, on the driveway. Holding the downpipe still with my boot, I cut the lip of the flex-pipe from it using my angle grinder.

Before I started, I ordered a brand-new catalytic converter, thinking that the one that was on there was 10+ years old, and of unknown working condition. After spending many hours cutting through rusty bolts with a hand-held hacksaw blade, I do NOT want to do this R&R again even if the fasteners are new. So, I'm grateful I made that purchase decision. After I got the cat on the ground I could see the Audi symbol on it, so either it was replaced at a dealer a long time ago or it was the original. Either way, at almost 300k miles, it is unlikely that catalytic converter was still doing its job well. Well enough to pass Oregon DEQ? We'll never know. Besides, the old bolts are rust-attached to that old thing, so re-install would have been considerably challenged.

new cheap hanger
On the other end of the hole in the exhaust, I removed the mid-pipe (2 bolts), cut off the remains of the flex-pipe with the death wheel and re-installed the mid-pipe. I added a support immediately behind where the flex-pipe-to-mid-pipe joint will appear so it is held up and away from the ground better. For the support, I got one of those cheap bolt-on hangers, attaching to the rear of the transmission through an unused bolt hole in the rear of the case.

Cat In
Moving back up front, I installed the new cat first, re-introducing the original O2 sensors as I went. To the cat, I added the down pipe and then finally connected the down pipe and mid-pipe with the flex pipe, fitting things together with clamps and exhaust dope. 

I got Nemo back on the ground to take him for a test spin around the usual neighborhood track. Before backing him off the ramps, I checked the exhaust for leaks, and it looked good, with a little puff of smoke coming out the tailpipe. The exhaust sounded much better, and it doesn't leak. So, around the block we went. It still hangs low, but it is fairly well tucked up under the body compared to before. The rear end ride height is so low, there is a near-constant threat of bottoming out. I will need to resolve that soon. He drove great; plenty of pull from the turbo, and the exhaust was much quieter than he had been on the last test drive. Clearly, the noise and smoke is going out the tail now. I thought I might have heard the rear passenger wheel bearing, though, so there may still be more adventure coming. And, yes, you can drive a car with failed power steering; you just need forearms like Popeye if you need to turn the wheels when the car is not in motion.... like to maneuver it out of a shop bay into the driveway through a 9 point turn. 

Oh Two
Oh Nemo.... O2
Unfortunately, the CEL is still on, with a code (P0134) indicating that the upstream (before cat) O2 sensor is bad. When I considered the smoke puff out the tailpipe when it was sitting on ramps, this makes sense: if the computer doesn't know the air-fuel mixture sent from the O2 sensor, it sends a richer fuel mixture to protect the engine from being too lean, which is why a failing O2 sensor is a DEQ auto-fail. So, I ordered a replacement upstream O2 sensor and now I'm waiting on shipping before I take another test. Since the error code did not include a code for the downstream O2 sensor, one might think that the old catalytic converter was still working. As I pondered this, I picked it up from one end, and I could hear dust settling through it. So, even if it wasn't toast, it was soon to be. When the new O2 sensor arrives, I'll slap it in, clear the code and go for a spin. If the CEL doesn't return, we may take him through DEQ before the next update. 

That's it for today. Like I mentioned at the top, the sanding on Zed continues. After sanding him smooth with the 320-grit, I did not like some of the orange-peel effect I found underneath, so I sanded the primer end-to-end with 320-grit again. Thanks, as always, for following along-

Tuesday, June 1, 2021

Oh, Nemo

Today's post covers my challenges with Nemo's electrical and computer system simply trying to get him to start, or maybe a signal on the OBD-2 port. The car-work hours that I did not want to spend sanding on Zed, I spent doing this... until this took over. Yeah, I know. I could use another hobby.

No Start
Like so many issues with these old cars, our challenges with Nemo started with him not starting. His battery had been sitting on a trickle charger all winter, but I had left his hood cracked to make room for the alligator clips, so this ultimately was self-inflicted. Love those. But, the path we took to get there was interesting. Nemo is sitting under the fabric carport blocking a garage door. Behind that garage door sits Oliver, the 1978 MGB convertible, that I would very much like to be road testing and otherwise driving around. So, enter my motivation for moving Nemo. Insert key, turn ignition to "RUN". I see some familiar idiot lights, including the battery, oil and check-engine. Turn to "START" and he rev'd but would not start. I went around to the tailpipe and could not smell gas, so I start with the assumption that it is fuel delivery.

Before I did anything else, I considered what I experienced when I turned the key to "RUN". I did not hear the fuel pump cycle. I did not hear the radiator fans kick on. So, something is not getting the "RUN" signal. So, I pull out the UltraGauge and plug it into the OBD-2 port. I get a never-ending "scanning..." message. Well, that's not good. I double-checked the UltraGauge in Hapy, and the computer linked within a few seconds. Okay, we have trouble with Nemo's diagnostic system which could prevent a start or we have multiple things going on. With this car, the latter is probably true. First, I tried to isolate the OBD-2 issue, and kill many many hours doing so.

OBD-2 Issue Diagnosis: General
The early B5 versions of the A4 had some interesting 1 or 2 year only issues. One of the oddities around 1997, when Nemo was sold, was the engineers choice to integrate the stock stereo with the "K-line": the signal processing wiring between the computer, many components and the OBD-2 plug. In these late 90's cars, it is the K-line you are subscribing to, not the more modern "CAN BUS". Okay, cool. There are many modules plugged into the K-line, but they are all in parallel. the diagnosis theory goes that when you get no signal on the K-line it is because one of the modules is faulting out, grounding the K-line. Once you can identify and remove the faulty module, you will get a signal on the K-line. You will probably get a failure code for that module, but you will at least get a signal. So, away we go, trying to figure out what modules are even on the K-line, and then isolating them.

OBD-2 Issue Diagnosis: Radio
The stock radio wiring was unceremoniously cut to pieces by the idiots at Car Toys when they installed an aftermarket stereo. Based on the wiring diagrams I have found and the commentary on the interwebs, I am not sure this car actually had that K-line-in-the-stereo thing. I did check the wires for the right color combinations, and for wires that were the correct colors for the K-line. I was unable to find them. There are, however, many wires sticking out of the hole where the radio used to be... before it was ripped off in Eugene. I intend to re-integrate an original plug before I put all this back together, but that's another day. I moved on to the next possible culprit: the climate control system.

OBD-2 Issue Diagnosis: Climate Control
found in climate
computer
The climate control system in these cars is another little computer. In some models, it is held in place with a couple brass clips. In Nemo, I had to remove the center console cover plate / face and found 2 Phillips screws holding it in. Once threaded out, the unit removes through the front. I unplugged the unit and checked the OBD-2 for a signal. Nope. I did, however, find a soda/beer can pull tab inside it (picture on the right, here, laying on the carpet after I removed it from inside the climate control computer thing). So, that was interesting. Next.

OBD-2 Issue Diagnosis: ABS (Brakes)
The fine folks on the interwebs have found that the ABS sometimes causes K-Line problems. The way to identify if it is the problem is to disconnect the plug. The ABS unit is on the driver (left) side, next to the washer bottle. You simply pull up on the silver metal tab and the plug lifts out of the socket. I found a piece of electrical tape floating around in there. Another question-mark from the prior owner. Neat. I checked the OBD-2 for a signal. Nope. I shot the socket and the plug with DeOxit and left it disconnected for the rest of my tests. I figured I might as well leave it better than it was (DeOxit, not leaving it unplugged). Next!

OBD-2 Issue Diagnosis: Dash Cluster
Moving on, we consider the dash cluster. The entire thing is held in by 2 Torx-head screws from the front, hidden behind a cover plate just above the steering wheel. Pull the cover plate, remove the screws and it pops right out. I unplugged the various cable plugs and checked the OBD-2 again. Nope. Grr... Next!!

OBD-2 Issue Diagnosis: ECU
example A4 ECU 
It seems like every system on the engine that has more than one wire into it delivers some signal to the computer. So, this seemed like the next logical step. I figured if I could get a signal after unplugging the small plug on the ECU, I would have shown that the issue is in the engine compartment and I could put everything in the cabin back together again. If the issue remains, then it could be the ECU. So, I disconnected the small plug from the ECU and we still didn't have a K-line signal. Grr...

So, I plugged the ECU, ABS and the dash cluster back in, turned the key to RUN and heard the click-snap of some relays firing, but no fuel pump nor fan spin. I could not remember if I heard the relays before, but this changed my thinking. If at least some of the relays are firing, then the ECU is telling them to. If there is a Check Engine Light, then the ECU must be at least partially working. Perhaps the K-line / OBD-2 issue is completely unrelated and this is just a simple fuel supply issue. So.. new plan: get the fuel pump to fire.

Fuel Pump Test
As is so often the case in laboratory settings, the pre-work for the experiment is where all the time is taken. Such is the case here. I started by removing the plate covering the fuel pump. This sits behind the rear seat in the trunk on the passenger (right) side, and is held in place with 3 very short Phillips screws. Once the plate is removed, you can see the top of the fuel pump. There are 2 fuel lines, one supply and one return, and a single electric plug. I found that slightly wiggling the plug allowed it to pull off the pump. YMMV. Once removed, you will see 4 pins. 2 of them are for the fuel level and 2 are for the pump. I started my tests with basic resistance and continuity-to-ground. Things seemed fine, so I shifted focus to test-firing the pump by applying 12V to the pump.

This is where the experiment set up took some time relative to the actual test execution. I ran a pair of wires from near the battery (not hooked up) back to the fuel pump. At the battery, I taped 10A fuse to the "red" wire and alligator-clipped the other side of the blade to the positive battery post. I alligator-clipped the "black" wire to the negative post. Back at the fuel pump, I applied the red and black wires to the fuel pump and it fired right up. I held the wires there a few second to demonstrate that it would not just run for a second and die. So, we have a good pump, but the pump won't fire from a relay signal. So, next we check the voltage from the relay, after we put the experiment wiring away.

Fuel Pump Relay Test
A4 Fuel Pump Relay
Back up front, I took a red wire, stuck it into the voltage-supply pin in the wiring plug at the fuel pump and tossed the other end through the cabin, over the outer edge of the driver seat. My plan was to compare the voltage sent to the pump at the pump. Since the relay only pops for a second when you turn on the ignition, I had to have my test equipment near the ignition key. I stuck my black lead against the metal fuse box mount, held the red lead against the wire I tossed through and turned the ignition to "RUN". I got 5V. I checked other spots around the fuse box and got 13V, so I started thinking that the relay was bad, dropping the voltage from 12/13V to 5V which, of course, is not enough to run the pump. So, I swapped out the relay... and the fuel pump still would not run. Great. I concluded that the 5V I read was actually the base charge for the fuel level sender and not the supply for running the pump. 

So, I checked the voltage at the supply-side of the relay: 13V. I jumpered across the relay pins, and the pump fired up. So, we're back to the ECU is not sending a signal. Fearing it is the ECU, I went looking for any other reason. I recalled that when Dot (the white 2000 VW Jetta 2.0 which broke the timing belt) failed, one of the theories for not starting was a crank position sensor. The thinking is that if the ECU doesn't know where in the revolution the crank is, it doesn't know when to fire, so it doesn't try. It is not as clear whether a failing crank sensor would prevent the fuel pump relay from getting a signal from the ECU, however. As much as I have tried to avoid it, it felt like I was sliding into just-swap-parts problem solving. At $35US for the least expensive part-to-swap (crank position sensors start closer to $60US), this can get needlessly expensive very quickly.

Crank Position Sensor (CKP)
A4 Crank Position Sensor
I have mentioned before my belief that the Audi engineers are sadists. Only someone who takes pleasure in other's pain could arrange for replacement items to be so hard to get to. Case-in-point: the crank position sensor. The crank runs the length of the block (obviously), so given a blank canvas, an engineer could potentially place a sensor anywhere along that axis. Chosen location? Directly under/behind the oil filter so you either have to remove the oil filter (forcing an oil change, which arguably is due) OR you need to perform contortions to get an Allen-head wrench in there. If you go this route, consider that the further the bolt comes out, the closer you get to the oil filter. At least there is only one fastener. These sensors have a long lead on them that plugs into the engine harness... behind the coolant bottle. In Nemo's case, this plug was fairly easy to get to. There are methods for testing the sensor, of course.

The Audi/VW sensor has 3 wires, from pin 1-3: power | signal | ground where the power and signal connect to the ECU and the ground finds its way to the chassis. To test, 12V and ground need to be supplied to the sensor plug (once disconnected from the harness) and a multimeter checking the signal wire for an AC wave signal while the engine is turning. No signal = bad sensor. Since no local shops had a CKP, I returned to sanding Bondo in Zed while I waited for the part to arrive.

Once I had the part in hand, I checked the resistance between the pins. I got 500ohms +/- between the middle pin and one of the outer pins. Using that as a baseline, I swapped out the CKP and then tested the one I had just removed. Same resistance. So, I concluded there was nothing wrong with the old one and put it in the stash of A4 spare parts (with the fuel pump relay).

ECU Swap
At this point, I had run completely out of ideas fo4r why the ECU was not sending a "go" signal to the fuel pump relay. I hit the local junkyard looking for a just-dropped-off A4 to scavenge the ECU. None of the A4's there had the right ECU, but I did get an ECU box cover: Nemo's had a good-sized hole in it where I thought water might have entered. Without another option, I hit eBarf and found an ECU with the same part number as the one as was currently in Nemo at a salvage yard on the East Coast (with a 30 day return policy!). Hopeful, I swapped out the ECU's which consisted of pulling out the big plugs in the back of the old and plugging them into the new one, since the box was still lid-less. I had some concern that energizing the ECU could fry it if the underlying condition still existed.

Still, I turned the key to "RUN" anyway... and heard the radiator fans and fuel pump cycle for a second before shutting off. This was how things used to work. So, I turned to start and he fired right up. I have concluded that my first guess was the correct one: I had left the hood open a little bit to make room for the alligator clips on the trickle charger, and with the hole in the ECU box lid, water got into the ECU and partly fried it. If I had not had the experience with the chipped ECU for Hapy when the computer semi-worked, I would not have been so quick to accept this. The Check Engine Light lit, so the A4 chat-boards all assume that means the ECU is fine. NOT TRUE. It could be partly damaged, like Nemo's.

The climate control is still in pieces, the lower dash panel is off, and the radio wiring, well, it's the same as it was: a mess. While I can move Nemo out of the way so Oliver can go for a spin, Nemo is not ready for driving around just yet. The re-assembly will wait, and I'll probably post on at least the re-wiring of the stereo plugs that the idiots at CarToys cut apart. I did, however, install the ECU box lid, complete with threading in the screws to hold it tightly shut. No more water getting in there.

Thanks, as always, for following along-

Tuesday, January 26, 2021

P0121 - the 1200 rpm limp mode - Part 1

Today, I will start to go through my efforts to identify the cause for my P0121 - Intermittent Signal from TPS issue. Yes, I know! Another multi-part series?!? Well, that's how it goes when we need to wait for shippers. Anyway, the process I followed is similar to what I did for the other wiring issues I just resolved in that there is a logical approach, but otherwise, this is about solving a 6-wire circuit and really shouldn't be a big deal. But it was and here we are.

Drive-by-Wire
drive-by-wire pedal
For those who haven't suffered from this code before, or may not even know this is the code you are getting, I'll start with a quick summary of what this is about. In modern drive-by-wire cars, your throttle pedal may not actually control the speed of your engine or vehicle directly. If you have watched some of the car shows on MotorTrend, when an older car (pre-fuel injection) gets a modern engine (with fuel-injection), they need to add a throttle position sensor (TPS) to tell the computer how far open or shut the throttle is. In these conversions, the TPS is usually connected to the throttle cable in the engine bay. This converted the pull/push of the cable (which reflects the push / let-up of your foot) into a signal the computer understands so it can figure out how much fuel to throw in, or how to adjust the timing of the spark. Cool, eh?
 
New cars, whether they are burning volts, waste cooking oil or dead dinosaurs, do not have a go pedal hooked up to a cable any more. They skip the middle man and have a TPS wired up to the pedal, so your pedal works like a big fader (light dimmer) or rheostat. The TPS converts your foot push / let-up into different voltage that gets sent to the computer where it does all the things I mentioned above.

P0121 - What Is It
All this is great. I mean, having something that precisely collecting your speed wishes and implementing them without a mechanical component seems pretty fantastic. And, it is, until that day when you are driving along and suddenly the pedal no longer seems to translate into speed. You notice that no matter how you position your foot, the engine speed doesn't vary. In fact, you note that the engine's speed has become static. I can't speak for other makes and model years, but if you are in a VW TDI circa 1998-2004 the engine will be pinned at 1200 rpm. Adding color to the scene will be the illumination of the check engine light. Your first impulse may be "oh snap, the engine is broken". Not so fast. In this case, you are probably getting code P0121: Intermittent Signal Inconsistency from the Throttle Position Sensor.

That sounds awfully scary, but in cars that were not hacked up like Hapy, this is probably caused by your TPS failing. It happens. In VW's, this is one of those rare parts that do not fail super-often, but when they do they are actually kind of easy to replace. You remove the panel under the dash, unplug the flat-connector, remove 4 bolts and it's out. Replacing the one in Hapy is just as easy, but determining that the TPS is the root cause is not. In Hapy, we have 6 circuits running through 7 meters of wire and multiple connectors. In your car, the 6 circuits probably run for less than a foot and run from that flat-connector to a T10 or something similar. No extra connectors, no super-long wires.

Hapy Diagnosing Plan
Before I pulled out my multi-meter, I gave myself a few minutes to think about the situation. I had intermittent P0121 codes getting thrown since I before swapped out the original 1998 NewBeetle one-year-only TPS for the more general-use one for model years up through 2004. The original TPS had the 6-wire bundle pressed against the underside of the bus, and eventually the plastic wire casings wore through. The wires grounded against the body, causing the original P0121 errors. The general-use pedal threw codes intermittently and was one of the drivers for the replacement of those wires with the front-to-back cable. That cable runs from just after the flat-connector all the way to the blue T10 (through another T12 connector). So, either some part of the wiring was done wrong or it was never the wiring all along, and it had always been the TPS or the flat-connector or both.
 
A side note about the wire sizes. The wires coming out of the VW 6-pin flat-connector vary in thickness from 22 or 24 up to maybe 18 (probably more like 20). Since the resistance of the wire is inversely related to it's thickness (thinner = more resistant), by replacing the old thin single wires with a thicker well-jacketed cable, I effectively reduced the resistance of the front-to-back run. According to this calculator, the wires in the new cable should be around 0.03 ohms. The old wires, being 22AWT gauge were around 0.3 ohms. Noting the decimal point, the old wires were 10x more resistant to current. So, we can exclude any concerns about the new cable wire size being a cause; quite the contrary, it should be delivering electronic messages better.

A failing TPS or a bad flat-connector sound like great theories. Let's prove it. I chose to start at the flat-connector and work back to the ECU. I have a second flat-connector in the heap of spare or removed TDI stuff in my garage that is also 6-pin, so I can swap-out the in-Hapy one if necessary. This also provided me the resistance values for a 6-pin flat-connector that is otherwise "normal". With the multi-meter at its most sensitive setting, I tested the resistance of each pin -to- end-of-wire. After the plug was warm in my hand, the resistance value was "3". Prior to that, when it was cold from the garage, the resistance was closer to "8". Since they were all within the same order of magnitude, I wasn't too concerned. That's our baseline: less than 10 on the most sensitive setting. With that, we bundle up and head back out to the bus.

Hapy Wiring at TPS
6-pin to
front-to-back cable
First, I unplugged the flat-connector, peeled back the plastic wire protector to where the wire splices were and then, with a razorblade, cut a small slit in each cable wire just past heat-shrink so I could touch metal with a probe. You can see the repairs to the wires in the picture on the right. The blue wire is probably the best visual example. Then, from 1 to 6, I checked the resistance to make sure they were all less than 10 on the most sensitive setting. To keep variables down, I held the flat-connector in my hands for about a minute first. It is still cold (4*C) here, even if I'm not complaining about it in every post. Apparently, its not a cold winter, I'm just a sissy working outside in it. So be it. Anyway, they were all very low, like at or below a "2" on the most sensitive setting. This told me that the flat-connector was good and the wire connections between the flat-connector and the cable were good. Very good, actually.
 
While the 6-pin flat-connector was out, I addressed the TPS plug socket with DeoxIt D5 according to the instructions on the can. I figured that if our problem was a simple case of the contacts getting worse over time, we would see a some improvement from this. I covered the little slits with electrical tape, and took a picture so I could reference the color-to-color later. I re-wrapped the wires in the plastic covering and moved to the back of the bus. I left the 6-pin flat-connector disconnected so the contacts could air dry.

Hapy Wiring at Engine Bay
T12-to-donor (T10 blue)
In the engine bay, I confirmed that the blue T10 and grey T12 plugs were snug. I would have had other issues if they had not been, but diligence wins electrical issues. Then, I pulled back the plastic cable wraps and took a picture of the T12 wires from pins 1-6 and then a picture of the color-to-color connections from the T12 to the wires which run to the blue T10. I compared these pictures with the wiring diagram I had constructed and believed all of the wires were routing to the correct partners. So far, so good. The next test was to confirm continuity between the blue T10 pin and the originating pin on the 6-pin flat-connector. This would demonstrate that the wiring from end to end is clean.
 
I was not really sure what to expect, resistance-wise. Before I could do anything, I needed to close the circuit, so I grabbed a long solid-core wire I have used to test with in the past. My testing process: I would gently insert a bare wire into the pin-hole in the flat-connector, and run the rest of the wire spool back to the engine bay. There, I measured the resistance between that wire end and a pin in the blue T10. I had difficulty figuring out which pin was "1" versus "4" in the blue T10 and the pattern from wire to pin seemed illogical. Unfortunately, had I really internalized that, I would have potentially found the root issue. When I found a connection, the resistance was down in the single digits in all cases. So, we can rule out the new wiring... ish: I discovered later that when I wired up the blue T10, I crossed up 3 of the wires. I didn't realize this until later (hence the 2-part post as I lost a bunch of time going down a wrong road). So, I continued forward believing that the wiring was right. Since I learned a bunch about the pedal along the way, I felt it was worth retaining all of this content.
 
Hapy TPS
Since I thought there were no wiring issues, I figured that the TPS went bad. I first thought that maybe I broke it by stepping on it all the way to max, and it needs a movement stopper or something. I looked at the way I installed it; the floor and the carpet would have acted like a prevent against over-pressing the pedal. After doing some research, it seems like these pedals are prone to failure if they get wet. Since Hapy is parked outside, and last year his fancy BusDepot cover effectively held water in rather than out, if the pedal had been steadily degrading because of the damp conditions over the winter (and sometimes in the Summer around here), then this seems a fairly reasonable explanation for the persistent, recurring P0121 code. I figured that last winter's super-damp caused the pedal to finally fail so I ordered a replacement.
 
That's it for today while we wait for the replacement pedal to arrive. More next time about resistances, voltages, etc as I examine the pedal and the pedal wiring and, ultimately, fix the P0121 error.