Showing posts with label reservoir. Show all posts
Showing posts with label reservoir. Show all posts

Tuesday, February 22, 2022

Burying the Brake Reservoir

This shorter-than-normal-but-actually-reasonably-length'd post was originally included within the second Hapy Seating post (See Hapy Seating - Part 2). I pulled it out into it's own post because the content stands on it's own, and the seating post was pretty long even without this. So, today, I will document the moving of the upper brake reservoir in the 1972 VW Bus.

Stock Reservoir
before image
Consider the original location of the upper brake reservoir on the 1972 bus is a tab/perch that juts forward from the driver seat partition. I clarify it by year because from the pictures I have seen, the reservoir appears in different places for different years. In Hapy's case, this perch sits, maybe, 6 inches off the seat floor with an opaque hard plastic hose attached to the bottom. The hose has a bulb at the top, allowing it to fit over the nipple on the reservoir. It is held on with a plastic clamp, and there is a rubber sleeve between the inside of the hose/bulb and the outside of the nipple on the reservoir. This opaque plastic hose runs down to the seat pedestal floor, and passes through a special hole in the floor of the pedestal. Within the pedestal, there is a cavity about 4 inches across between the inner wheel well of the driver front wheel and the outer edge of the pedestal. The opaque hose runs downward into this cavity and out a hole in the floor of the bus. Underneath, the hose runs forward about a foot to the master cylinder, upon which is another reservoir, that the hose attaches to. The hose connection to the lower reservoir is the same as the connection to the upper reservoir: bulb, clamp, rubber sleeve. Between the bulbs, the hose is narrower. The picture on the right, here, is from Hapy before I replaced the hose the last time. Note the rust, but more importantly, note the tab on the partition. Also, near the lower right corner of the rear-most square opening is the round hole through which the original brake reservoir hose passes. I do not have a picture of my original, complete, assembled set up, nor can I find any examples on the interweb. Trust that a square-ish reservoir hangs on that tang and connects to an opaque hose that passes through that round hole.

Gimme a Brake... Reservoir... Hose
pre-paint test mount
A while back, when I took that picture above, I purchased and installed a replacement opaque plastic hose between the remote, upper, brake reservoir (behind the driver seat) and the sitting-on-master-cylinder lower reservoir, but I did not shorten it to fit. It was "the" hose that was available, and was described as the right part for all buses and Vanagons. One size fits none again as the upper reservoir did not sit where it was supposed to. Just to hold it still, I zip-tied it to the driver seat partition through a pair of factory threaded holes near the top crossbar. It was not pretty, but it was functional and it didn't leak. So long as the driver seat was pushed back, no one could see how ratty the solution was. 

I wanted to fix this ugliness. I had mentioned the location of this reservoir in passing in the first post about the Sprinter seats (See Hapy Seating). I thought about the reservoir, it's location and the hard plastic backside of the 2016 Sprinter seat, concerned whether the brittle plastic reservoir in the original position would get run into if the seat was pushed back to the partition. Fairly sure the two unforgiving plastics would hit each other, potentially cracking the much older reservoir, I moved it inside the pedestal of the front seat. It can now be accessed through a pre-existing square-ish hole in the pedestal, near the rear of the seat. The picture on the right, here, shows the new location. I may get creative with a cover when I do the carpet or I may leave it exposed, but that's a decision for another day.

Re-Locating the Brake Reservoir
I started by MityVac'ing a bunch of brake fluid out of the hose, down below the stock mount point. Before I made the decision to simply move the reservoir, I tried to shorten the plastic line. I cut the hose, heated it up and tried to force-jam it onto the filler. Yeah, that doesn't work. I could not figure out how to make the "one-size fits Vanagon - otherwise you're on your own" hose to fit. Additionally, the plastic is too hard to wedge a 2-sided nipple in a line breach, so a simple cut and double-barb solution wouldn't work. I abandoned that plastic line and started seeking a rubber line solution.

reservoir in service
The hose barb on the original reservoir accepts a 12mm hose. Flexible 12mm brake hose is not easy to find in lengths greater than 4 inches around the usual online sources for some reason, and those short sections are crazy expensive (like $8US before delivery charges). However, a half-inch hose is only .7mm bigger, and those are plentiful, here in the US. So, I ordered a 2 foot length 1/2" Department of Transportation (DOT) -rated brake hose, and ran it from the master cylinder up under the driver pedestal, through the original hole in the floor. The hole through the floor needed to be expanded, however. I do not have drill bits that big so I used a sledge-hammer and an old 2-ton floor/trolley jack's removable handle (as a chisel) to smash the hole larger. Yeah, that felt a bit destructive, but it only took about 4 or 5 whacks with my small sledge to drive the jack handle through. The jack handle was completely unmarred by it. Once expanded, the hose slid through the hole.

I fit the upper connection first, and completed with a clamp. The hose settled onto the plastic nipple, but I unexpectedly needed to use a touch of force. I had thought that .7mm would have allowed the hose to slide on and slop around. I was pleasantly mistaken. Then, I slid underneath and figured out the correct length of hose. Once the length was decided, I cut it with tin snips, and mounted with a clamp. I mounted the upper reservoir to the side of the seat pedestal last, filled it with brake fluid and checked for leaks. I stepped on the brake pedal a few times to create some pressure. Finding no leaks, a firm brake pedal and feeling quite satisfied, I called it complete.

Oh, the 2016 Sprinter seat easily slides back over the top of the reservoir with plenty of room to spare. Like multiple inches to spare. As to what would have happened had I pushed the seat all the way back, I'll never know for sure. But, the rear of the seat comes within an inch of the little tab thing, so they would definitely have collided.

That's it for today. More next time-

Tuesday, May 28, 2019

Brake Fluid Replaced

When I had the wheels off, I tested the brakes, replaced some parts and replaced the brake fluid. Today's post covers that adventure.

Brake Check
The wheel saga I just recently posted about all started because the camping festival season is coming and I wanted to make sure my brakes were up for another season. I had remembered that my old rear hydraulics were bad and I hadn't checked the wear since the beginning of last season. Even then, it was a visual without removing the rims. So, after I got the wheels off, I checked things off.
Front pads: 60% remaining
Rear shoes: 70% remaining
Front rotors: unblemished along friction surface, rust along outside edge
Rear Drums: some scoring
Front calipers: unblemished, bleeder caps missing
Rear hydraulics: some surface rust, one bleeder cap missing

This was a far better state than I feared. I knew, however, that the brake fluid hadn't been changed in a long time. I couldn't remember doing it, but I must have when I replaced the rubber lines on the corners. That would have been 8+ years ago, so that fluid is way past due.

DOT3 or DOT4
Sometimes, I think the internet is the great religion creator. If you have a relatively straightforward yes/no question, you can find all kinds of long treatises waxing the pro's and con's but getting a real yes or no can be nearly impossible. In the case of DOT3 or DOT4 brake fluid, I have found some level of consistency, which I found rather surprising. So...can your older car which required DOT3 brake fluid can use DOT4: Yes. Can your newer-ish car which required DOT4 use DOT3? Only in tiny quantities, with the expectation that the system will be bleed-filled with DOT4 later. In other words, if you are running low on fluid and somewhere that you cannot buy DOT4, you can put in some DOT3 to get you back to civilization. DOT3 cannot handle as much heat as DOT4, so to prevent failure of your DOT4-requiring system, you should stick to DOT4.

As to me, and the old bus, I can run either. DOT4 can handle higher temps. Some folks say the DOT4 absorbs less water (and that's why it can handle higher temps), so you can change it less often. Like any good pseudo-science, there are great theories (sometimes with great single-experience stories), with little science, to support both of those claims. Enter religion. Regardless of whether they are accurate, I chose DOT4 for the higher temperature tolerance. I will assume that I need to change the fluid on a 3-year interval just like I was supposed to before. I was apparently a brake-system sinner before, letting it get so outdated.

Vacuum or Pedal
Once you decide on the fluid, you need to arrive at a method. If you have a helper, I encourage the pedal method. If you don't have a helper, but you have a MityVac, you can do the fluid change with it. Take ibuprofen first; your wrists and hands are going to hurt later. Regardless of your choice, the pattern is the same:
keep the reservoir topped off with new fluid while bleeding old fluid out of the bleeder furthest from the master cylinder. Once it changes color, and stops changing color, move to the next-furthest bleeder. Don't let air into the system at the bleeder or you will have that to deal with. Move from furthest to closest wheel until you've done all 4.

New Reservoir Hard Hose
I have come to realize that any time I am touching a system on this 50 year old bus that I haven't touched for a long time (or maybe ever), I should assume that any rubber part will need to be replaced. And, I should assume that I may touch something else that will fall apart on contact while the one thing I'm trying to get apart will require acts of God to get them separated. Never was this more true than the little rubber bushings that snug the connections between the hard plastic hose and the 2 brake fluid reservoirs. Yes, this bus has 2 of them. There is one sitting on top of the master cylinder like any normal car. We'll call this the lower reservoir (LR). Attached to the side of this is a plastic hose which runs up behind the driver seat to another reservoir. We'll call that the upper reservoir (UR). To be fair, it is much easier to add fluid up there, so that's probably why they designed it that way. The hard plastic hose stays connected to the hard plastic reservoir because there is a little rubber bushing between the plastic parts and then the whole thing is cinched together with a plastic thing that looks like a hose clamp with a slotted screw holding it together. Very sketchy. I figured the rubber bits on mine were gone, and that the damage to the steel behind and under the driver seat was caused by leaking brake fluid. The fact that fluid didn't stay in the UR for very long supported this theory. Knowing that parts on this old bus are either falling apart, rusted or otherwise seized, I got replacements for the hose, the rubbers and even the UR. I only ordered one grommet, and it turns out I needed 2. Check twice, order once. Don't assume the websites know your bus; you have to look yourself.

NLA
Unfortunately, the hard hose in its original length is no longer available (NLA). Only the Vanagon hose is available, and it is at least 8 inches longer. Longer is better than shorter, I suppose. That's definitely true for summer days and early Dark Star's, but this is a hard hose, so putting a few bends in it to make up the slack is not an option. On each end, the hose is fluted to fit around the nipple on the reservoir, so even though the web sites all say to cut the hose to length, that's all fine until you want to install it, and then the cut end won't fit on the nipple. And, because you cut it, it is not returnable. So, I suggest you don't cut it and do something clever... like I did.

You have 2 options:
(1) cut 8" out of the hose in the middle and figure out a way of joining the 2 ends without creating a new leak source or
(2) keep the hose the way it is and figure out a new way to attach the UR to the short wall behind the driver seat.

I went with option 2, knowing I could always fall back to option 1 if I couldn't get it where I liked it. The UR is basically a cube with a filler cap along one edge, pointing away from the dead-center of the cube at a 45* angle. Originally attached with the cap facing forward, this made filling easier than having it smack on top. We can use this angle to our advantage. If we rotate the reservoir 90* so the filler cap faces the center of the bus and then tilt the hose towards the door frame, eventually the cap faces straight up. It can be mounted to the wall like that. Before you get too far down this path, assemble the hose, rubber bits, plastic hose clamps, etc to the various reservoirs. Connecting to the LR is swear-word generating-ly frustrating, so prepare with a loud radio and sending the kids inside.

Install Hose
LR image from theSamba
I started by threading the one grommet around the hose and then the hose from above down through the hole in the floor. Since I didn't have a second grommet, I did not want to cause the hose to fail prematurely, so I did not thread it through the little hole in the driver seat pedestal. Instead. I routed it through the large square hole immediately in front of it. This may make it more susceptible to getting struck by camping gear, but I rarely put anything behind the seat, so that risk should be low. It also looks quite janky, and I will probably want to solve it properly before I re-install pedestal carpeting. Regardless, I decided to go with option 1 because I wanted to get this on the road for test drives, and knew I could change this fairly easily later.

Anyway, once threaded through the hole in the floor, it settles onto the nipple of the LR. It takes prodding to get it to sit on the LR nipple without damaging the rubber bushing and getting it deep enough that it won't leak. For me, it took wrapping the hose with a rag and grabbing on with channel-lock pliers to force it on that last bit. I found that putting the bushing on the nipple rather than seated in the fluted end of the hose was more effective as well. Tighten on the plastic hose clamp with a slotted screwdriver. Circle-back to check for leaks later, once you've put brake fluid in.

schematic from VWHeritage
The UR is easy to assemble with the hose, if you don't cut off the end. Placement of the reservoir, in my case, is temporary while I figure out a better long term solution. Ultimately, I will probably do option 2, and cut out a section in the middle. If I can do it right, I'll make the cut between the floor and the driver pedestal so the cut solution is not visible once the pedestal carpet is re-installed.

That's it for today. We got the DOT4 through out the system, using the vacuum method for the rear and the pedal-pump for the front. While the vacuum works, I greatly prefer the pedal-pump method. It is much faster and you get to hang out with a friend while you do it. After a test drive, the brakes settled down into a predictable response as the air worked it's way back through the master cylinder and up through the reservoirs. After several longer drives, the UR fluid level has remained unchanged, and the brakes are consistent. The brakes are ready for another season.

Thanks, as always, for following along.