Showing posts with label marker. Show all posts
Showing posts with label marker. Show all posts

Tuesday, August 25, 2020

Dust Dodging

If, after my last post, you guessed that I was going to find something to do other than sanding old paint off of Zed, you were right. I just can't get myself fired up to do that. I think I'll just have to put in an hour here and an hour there or it will never get done. Seriously, I thought after the rain we got recently I would get all fired up, but... nope.

Passenger Side
It started with something so simple. I was sitting on my front porch, surveying the herd while sipping a beer as the evening turned to twilight. Like a beacon, the white trash-bag taped over the front passenger window of the A4 shined in the dwindling light. Yeah, that just had to get fixed.

So, off to the junk yard we go. I hadn't been to the yard for a while; long before the CoViD-19 thing hit. The scene is a little different now. Of course, lots of folks have masks on, and there's the safe-distancing stuff on the floor near the check-in / check-out counter. But, more than that, it seemed like the folks pulling parts were pulling parts for other people more than for themselves. I say that from partially overhead passing conversations. Regardless, there's something about the junk yard that I really enjoy. Sure, the conditions need to be right. The car you're looking for has the parts you want, and they aren't trash. Ideally, it isn't super cold or wet. When you hit those conditions, it is downright fun to pull parts. Today was that kind of day. I found a black 1996 Audi A4 Quattro that hadn't been picked over too much. Most important, it still had the front passenger window.

Removing and Installing A4 Window
window in
For all of the usual over-engineering that German cars suffer, the front window on the A4 isn't one of them. This is actually a very simple operation. The inner door card needs to be removed. It is held on by 2 small screws (one front, one rear) at the top. Usually, there are a pair of screws inside the door grab, hidden under a pop-out panel. Since the card in the donor and in Nemo had both been removed previously, these screws were gone. Once the screws are out, the door card lifts straight up, and then pulls away. The door holds the card with a cable connected to the inner door opener. This removes fairly easily. I did not have to touch this for the window R&R. Once the card is far enough out of the way for you to put hands on the window tracks inside the door, you're ready. Force the window slightly lower, like 3 or 4 inches. The bottom of the window needs to pass the inner structures enough for you to see where the window attaches to the tracks. Depending on the year, the window is held on with either Phillips bolts or Torx. One last item worth mentioning: shop-vac all of the broken glass out of the door and the floor. The floor part is obvious, but if you don't vacuum the door, it will have a cheap rattle of the glass bits every time you open and close it. Spend the 20 minutes and vacuum. You won't regret it.

The window removes and installs from the outside. When removing, lift the rear out first, with the front corner trailing. The install is the opposite, lead with the front corner and settle into the window lift-clamps equally. As you tighten the clamps down, pull/push down on the window to make sure it stays fully seated. Once installed, I decided to remove the after-market tint. I regret not doing it when it was out. I had to clean the window a lot after that, starting with peanut butter and then window cleaner but it looks like a normal window now.

While I was at the yard, I grabbed the front side lights, since Nemo has been missing his since T bought the car. I found a pair of fog lights from a slightly later model that I took, thinking I'd slap them into either Nemo or K'Lack later. Last, I pulled the front grille because the one on Nemo was painted flat black by a prior owner. Since leaving the yard, I have thought about going back for the hood since it is in such nice shape and the hood of Nemo has no sheen on it. Both the no-sheen and the black grille can be seen in the picture below.

Removing and Installing A4 Front Marker Lights
front marker in
Again, I was surprised at the lack of German car-maker hassles when it came to removing and installing the front side marker lights. First, open the hood. Above each of the 2 lights there is a small round hole in the front steel top that runs directly under the hood at the front. Slide a basic slotted screwdriver into that hole and find the small plastic tab jutting rearward from the light fixture. Press down on the tab and with your free hand, pull the light forward. It pulls out about an inch and then needs to slide a little bit to the outside, and then pulls the rest of the way forward and free. This makes replacing that bulb super easy. In my case, it was a very simple case of installing matching front side-markers. Once wired up (socket clicks in and is held with 2 small plastic tabs), the install is the reverse. No, really, it is. Set the housing into the hole, slightly to the outside, but oriented as it will look when it is in it's final position. The tab that you pressed down on above needs to find it's way around a vertical plastic bit. Then, the housing sets deeper, sliding towards the inside. Set the pins into the alignment holes and set it all the way back. It should "click" to let you know that the tab has reset.

Just like that, the A4 looks way better. There are other things Nemo needs, like finding the oil leak and fixing the trunk (latch broken). But, the easy stuff is done, and now it is complete. So, in theory, I can leave it alone and shift focus onto Zed. But I think you and I both know that just isn't going to happen. I just don't want to.

That's it for today. Thanks, as always, for following along.

Tuesday, March 31, 2020

More SIde Marker Lights

After my last post about getting the rear side-marker lights back on, the missing front side marker reflectors looked all the more absent. Today, I go through the effort to not just get them back on, but upgraded with bulbs. Trigger the purists' grumbles.

Side Markers Reflectors
Originally, these buses shipped with just a yellow reflector stuck on the lower front doors. I imagine it was because of some odd US DOT (Department of Transportation) thing to improve visibility. Nowadays, everyone has lights on the sides both front and back, so this is kind of novel, I suppose. Novelty aside, I want to increase the probability that I will be seen at night, since that is when Boo and I mostly travel to festivals. If you're lucky, your reflector looks like the picture on the right here. If you're more like me, well, it doesn't. Similar to my rear side marker lights, these reflectors were nasty with moss growing inside them when I bought the bus. I removed them (2 Phillips screws hold them on) and cleaned them until they were as good as I could get them. Then, they sat in a box for a few years... until today.

Run Electrical
hole cutting
The first step in converting the reflectors to lights is to run a signal wire from the neighboring front turn signal. In the early (sometimes called "low-light") bay window bus, this is straightforward. First, remove the lens (2 Phillips head screws) and then the housing (2 more chunkier Phillips head screws). Pull the housing away from the bus and rest it on the bumper. Knowing that the wiring could have been clowned with, I pulled on the headlights stalk to the parking/running light setting, and confirmed the light while sitting on the bumper is lit. With my voltmeter, I confirmed which of the 2 wires heading into the housing is the signal wire for the running light. In my case for the passenger side, it was the white wire. YMMV. Turn off the lights. Now, for some fun. Remove the inner door card on that side. This requires removing the window crank, the pull handle and the door release handle. Thread some wire, ideally the same color as the signal wire, through the front light housing hole from the front (front is front). In my case, I had removed the little switches that were designed to turn on the dome light when the door opened, so I have a pre-built hole to run the wire through. So, for me, I send the end of the wire up over the top of the metal air housing and out that hole and through the upper-most vent in the leading edge of the door, and down to the bottom of the inside of the door. You may need to run your wire another way, or put a hole in your pillar (I couldn't bring myself to do it, but your bus, your choice). In fact, on the driver side, I needed to thread through that hole first because of all the other wiring, the fusebox, etc in the way. Once strung, attach a basic female wire dis-connect onto both ends of the wire.

Bore a Hole
Once you have the signal wire dangling inside your door, you're ready to put a hole in the outside. Yeah, that sounds kinda scary, but the backside of the bulb-holder needs to stick into the inside of your door. Its not too late to back out. To locate the hole, find the centerpoint between the 2 screw holes that are used to hold the old reflector on. In my case, the holes were 3-inches apart so 1-1/2 inches made the center spot. With progressively large drill bits, pierce the door and then expand it enough for the centerbore of your hole saw to fit without any play. I found that a 30mm (1-1/4") hole was just barely large enough for the bulb-holder to fit. So, fit the 30mm hole-cutter onto your drill and cut the hole. Okay, so you're all-in now, but the rest is fairly easy.

Hook It Up
I pulled the rubber off the bulb-holder and verified which of the 2 posts are the ground, and which is the signal. In these simple circuits, it may not really matter, but I like to have it right so it doesn't bite me later. Once I knew which is which, I hooked up the signal-wire female dis-connect to the non-grounded tab. To the "ground" side, I attached a short wire which has a disconnect on one end and a ring terminal on the other. The ring side is held against the bus by the bulb-holder when it is attached to the bus. I taped the ring terminal to the housing, leaving the metal ring exposed, so it wouldn't fall off or shift during install. On the other end of the signal wire (at the original light housing), attach a dis-connect splitter (see picture) to the light housing and then connect the original signal wire to one side and this wire to the other.

looks stock, but there's a bulb in there
At this point, you should be able to pop a bulb into the holder, hold the grounding wire to some bare metal on the door and test. If everything lights up, you're ready to button it up. It is possible that the ground in your door is not reliable, so you may need to run a ground wire along the same route as the signal wire to the light housing. If not, send a couple Phillips screws through the yellow reflector, through the bulb holder, through the ring terminal and into the door. Then, re-mount the front signal housing and repeat on the other side. If you hadn't already, put your inner door card back on, and re-attach the window crank, door pull and latch.

Each side took me a couple of hours. Yep, I'm slow, but I have found that the faster I try to get, the slower I ultimately go. I hope you found this to be an easy, but rewarding little project for a period when you want to put some love on your bus, but don't want to get into anything too big. For these CoVid-19 days, just getting out of the house to do something constructive is rewarding.

Thanks, as always, for following along. Stay safe, wash your hands and practice physical distancing (but stay social)-

Tuesday, March 17, 2020

Side-Marker Lights

This is my first post since CoVid-19 completely took over the international conversation with cancelled professional leagues, concert tours and pretty much every other social outing. Boo hit the grocery for our usual restock and what she saw was out of a zombie apocalypse movie: partially filled carts strewn all over the place, shelves stripped to nothing in some areas (toilet paper?) and virtually untouched in others (fresh produce). And, of course, tons of people, having lost all sense of public-face calm, filling their carts with strange things like cases of Gatorade. People are weird when they're scared, or maybe they don't usually cook at home. Either way, the world is very odd today.

My employer has directed all of us to stay home and work remotely thru 3-April, so I expect I will be getting cabin fever stir-crazy quite soon. Since today is St. Patrick's Day, may we all have a little touch of the Irish luck and see this pandemic pass quickly. Anyway, where was I? Oh yeah. Side Marker Lights.

Side Markers - Original
When I first got Hapy, the side lights didn't work. I didn't think much of it since they were cracked and had nasty looking moss growing inside them anyway. Later, I removed them when I thought I was going to paint him. I got as far as priming him. I figure when I finally do get to painting him, I don't want to wrestle with the side markers. I figured I could do that now.

On the early bay-window bus, there is a single side marker light, located rear-ward of the rear tire, fairly low on the body. Each one is wired into the respective tail light for juice courtesy of the wiring loom. Or at least that's how they're supposed to be set up. Once I got into it, I discovered why my side markers didn't work: the wiring was gone. Just cut away. Oh well. No judging. I have done some things on this bus that will scratch some heads, but this left me with a puzzle.

Side Marker - Passenger Side
Without wiring, I decided that I would tap into the tail light, so I spliced off of both the housing ground and the running-light signal. This was fairly straight-forward with some female dis-connectors and some 16ga wire. Mounting the light was far more interesting. The old set up was falling apart when I took it off, and it was so long ago, I don't have a clear picture of how it was on there. If memory serves, the outer lens was held on with long screws run through the bulb-holder and into the side of the bus. When I tried to align the new holder, with the correct snap-in plastic buttons, there were no holes in the bus to pop them through. They had been filled with bondo prior to my getting Hapy. Sweet. I chose to drill holes where the holes should have been and then attach the holder with a pair of short screws through those holes. That mostly worked, and once the bulb was set I was able to successfully test that the wiring was good (see picture),

Side Marker - Driver Side
While pushing and shoving on the wiring harness near the driver side (looking for the side marker wires), I managed to cause a failure in the driver-side running light. I looked at the wiring diagram, and it looks like that bulb has it's own fuse and circuit from the fuse box. Since the fuse box only has, like, 12 fuses, I thought this was super weird. I was not going to run a new wire from the fuse box and this was not going to be the watershed moment where I decide to replace the whole harness (which, if you remember, I got when the ignition fried, and cannot return). Instead, I did a classic DPO move. I changed the wiring for the passenger-side side marker into a 2-wire splice, running a long wire along the original harness over the engine hatch to the driver-side tail light. At this point, I made a second 2-wire splice, sending one into the running light in the tail light housing and one to the side-marker.

Unlike the passenger side, the driver side had all of the correct holes. Unfortunately, this install showed that the replacement parts do not have a "pop-in" plastic nub that is long enough to actually snap the housing into place. Since the nubs are easily removed, I simply pushed a bolt through the housing and the side of the bus and threaded on a washer and nut from inside the engine compartment. I popped in a bulb, tested and then shifted to the lens. The lens set on easily enough, though they do not ship with screws/bolts so you're on your own for those. Once all assembled, I re-confirmed the running lights work all-around (again, see picture).

K'Lack Came Back
I intend to continue doing these low-risk things until I am ready to tackle 2 big projects on Hapy: (1) re-wiring the front-to-rear using a cable and (2) implementing a defroster. Both of those will be big, and I'd like some dry weather before I start them. But first, we finally got K'Lack (our TDI wagon) back from the transmission shop. Recall that K'Lack was suffering a form of morning sickness, being unwilling to shift out of first on cold mornings. I thought it was from old activators inside the transmission, so we took it back to the rebuilder to swap them out. That wasn't it. After 2 months of trying to figure out the mystery, they discovered that the rebuild kit they were sent for the rebuild a year ago was for a 01P not a 01M transmission. After trying everything else, they pulled the transmission, rebuilt it again and compared the servos to the ones they removed and learned that they are different sizes, but barely noticeably. Anyway, with K'Lack back in service, I can pull Oliver (the MGB) off the road and fit him with a catalytic converter before he is due for Oregon DEQ in May.

Remember how at the end of the TDI retrospectives (here) I said that there would be a gap in postings for a while as my projects got spun back up? Well, I think that's finally going to happen now that K'Lack is back. With 2 operational cars, K'Lack and Flash, I can comfortably take Oliver and Hapy out of service. So, the project fun is about to begin, but that means that the blog silence is as well.

Thanks, as always, for following along. There will be more when something I haven't started yet is close to completion. Wash your hands, for 20 seconds, many times a day, my friends --