Showing posts with label ignition. Show all posts
Showing posts with label ignition. Show all posts

Tuesday, May 11, 2021

MGB - Ignition Complete

My last couple of posts have spanned 3 weeks, and, honestly, most of the work has as well. Today's post ends with a running car, and covers the final step in the ignition journey.
 
Best Laid Plans
I thought my plan was so simple. I would just pull out a box of bolt-in ignition parts and I would go from a running-crummy car to a magical sled. As you have witnessed from the last couple of posts, it was not that simple. First, the battery was dead, then the fuel pump was bad. Now, we are finally ready to set the timing, but there doesn't appear to be any spark coming from this new ignition. Why?

Lucas, Lord of Darkness
First, that's not my joke; I borrowed it from Hal. Thanks, Hal. Years later, its still funny, and in so many cases, its still true.
Lucas CEI ignition wiring diagram

I figured that the red and black wires for the ignition signal in the new distributor could just re-use the red and black wires that had been feeding the old distributor. That was my mistake, because I did not recognize this was not your standard distributor. No... this was a Lucas CEI ignition system. While I imagine these were great in their day, this set up was a little more complicated. The 2-wire signal going to/from the distributor does not go directly to the coil. It routes through an amplifier box. This amplifier box appears to only work with the Lucas stuff, though. I believe that either the replacement hi-power coil, the new distributor or both are not compatible with the amplifier box.

The amplifier does not make things much more complicated: it only adds 2 wires to the coil, but the wiring around the coil is already a little confusing. Add in some extras and some grease shmears and trying to figure out what wire is for what starts to get more difficult, especially when the wires are not in the standard diagram. The image above is correct, but it is not in the standard "advance autowire" wiring diagrams, nor can I find references to the Lucas CEI in the MGB shop manual that I have. Still, this research did tell me that there is no ballast in the circuit from the coil to the distributor. There is a ballast between the coil and the fusebox (and that remained), but I figured I should be able to direct-wire the red/black wires to the +/- on the coil directly. The picture below should help show what a "ballast" coil set up looks like. See that "distributor resistor" in the drawing below? It is not in the drawing above so I don't have that. So, we start over. Kinda.
 
Final Install
standard 1978 ignition wiring diagram
I started by removing the distributor again. I had moved the 2-pin plug from the Lucas distributor onto the AccuSpark so I undid those solder joints and soldered on 2 1-foot lengths of 16ga wire (black and red for negative and positive, respectively). I heat-shrink'd the solder points. To the ends of these wires, I added female wire disconnects and heat-shrink'd those as well.

Next, I disconnected the wires going to and from the amplifier box and then removed the box itself. I re-installed the coil and the 2 things that shared the mount-points with 2 shorter bolts. Then, I slid the distributor back in, and re-set the mounting bolt to hold it firm. I had found TDC earlier, as noted in my previous post, so I oriented the distributor visually into the same place (took a picture before removing). In theory, everything should be fairly well set, at least well enough to start, albeit roughly. I optimistically pulled out my timing light just in case.

On an aside, the MGB battery is behind the passenger seat. This makes use of a timing light challenging. To remedy, I sat an old battery on the floor by the front bumper on the passenger side and clipped my positive and negative leads for the timing light onto it. 

It's Alive!
tidied up
I double-checked my under-hood connections, turned off the KBOO and then returned to the driver seat. I turned the key to run and heard the click-then-hum of the fuel pump as well as a click from the engine compartment. Thinking that was the coil leaping to life, I turned the key to start and Oliver started immediately. I mean immediately. No ba-ba-ba beforehand, no choke needed. He just started, and then dropped into a lope-y idle.

Setting Timing
Thrilled, I clipped my timing light sensor on spark lead #1 and pointed it at the main pulley. It flashed on the timing mark, indicating I was around 10* before top dead center (BTDC), which was in the ballpark (suggested 6-14 degrees advanced from TDC by AccuSpark). I tried rotating the distributor housing a little bit to advance or retard the timing, and found that Oliver was most content around 12* BTDC. My light is a cheapy, and does not have a knob to check full advance. So, instead, I used my ears, revving the engine up and down and then revving it up and quick-pulling my foot off the pedal. This last test was when Oliver used to backfire. There was none of that now. Of course, he is not under load right now either. Undeterred, I went back up front and checked his timing again: he was still settled at 12*.

I turned off Oliver's engine and tightened down the timing adjust set bolt (5/16") so the distributor would not rotate on it's own, and his timing would be locked in. I was done. Wow. I hadn't expected that. So, I spent a few minutes cleaning up some of the wiring that I had earlier cut loose from the taped loom by encasing it in some basic wire wrap.

leads now
I included the before picture of my ignition below (blue leads) and a picture of the ignition now on the right here (red/orange leads), taken from about the same spot. If you look closely, you will notice that the newly installed distributor is oriented at least 45* anti-clockwise compared to how it was before. So, either I had moved the dizzy a little before taking that before picture or the engine was running so incredibly off it is kind of a miracle it was running at all. Perhaps the backfires on deceleration could be attributed to the timing being so far off that the dizzy could not get back to a fire-at-the-right-time state when I took my foot off the pedal.

At this point, I'm not sure it was ever firing at the right time. Based on how quickly he started, and how well he ran after I revved him a few times, I am confident the mark I used for TDC and his timing are correct. The lesson here, I think, is to give your new-to-you car a tune-up as soon after you get it home as you can. I have been given this lesson before (See Bay City Blues), but I guess I need multiple examples before I learn sometimes. Bare minimum, I will start looking at my spark plugs during oil changes so I have a regular insight into the combustion. Might be worth a quick validation of the timing when I do that.

Next?
Oliver is pretty much ready to go again. He hard-started a few days after I did the timing I mentioned above. So, I still need some carb adjustment time, and he needs to go through DEQ, of course. An oil change is overdue as well. Otherwise, he is practically ready for Summer. As am I. Just thinking about a top-down drive with Boo for a picnic at a park sounds just about perfect. I'll post on the carb tuning when I get to it.

leads before
I'm not sure what I will be working on next, but nice weather is right around the corner so returning to the paint on Zed is inevitable. Some of him sat outside all winter, so I imagine there is quite a bit of rework coming before I can think about laying paint. Meanwhile, T is due back in the Pacific NorthWest to fight forest fires somewhat soon, and he will probably want/need Nemo on his off days. So, maybe I need to get that rear end sorted. Of course, Nemo won't start now or even put a signal to the OBD2 plug, so he is going from bad to worse fast.

Regardless, there's always something to do at ShadeTree, like helping a local kid swap out his muffler. Oops, I guess I forgot to post on that. We had fun and he learned something: a fart can muffler on an otherwise stock exhaust doesn't really do anything. For a meaningful change in tone and performance, he will need to remove at least one of the other resonators. He is saving up for a cat-back; that will be fun.

Thanks, as always, for following along.

Tuesday, May 4, 2021

MGB - Fuel Pump 2 Step

Picking up where we left off with Oliver, the 1978 MGB, we had completed the ignition swap out and we were ready to start the engine and set the timing. Until the battery went flat.

To Start Or Not To Start
should be an image from AutoZone
AutoZone product picture
At this point, I was ready to test-start it. Or, so I thought. Last Fall, I thought Oliver's battery was going bad. It later turned out to be the clock sucking all the juice while left sitting for weeks (see MGB Battery Monitoring). Before I learned that, however, I swapped the battery out for the battery from the donorZed. At this point in my electronic ignition install, I discovered that the donorZed battery actually was bad. I mean bad. Like, I would put it on the charger overnight and then I could put a voltmeter on it and watch it discharge down to 0. Fortunately, I had left Oliver's prior battery on the trickle-charger, because I guess I was not 100% convinced it was bad. So, I swapped his old battery back in. I turned the key, heard the fuel pump click once, and then heard nothing. In the past, I have had this happen when the fuel pressure had not let off since it was last running. Since the engine had not run since October, that was unlikely. Perhaps the inertia switch got nervous and is preventing the fuel pump? Well, then I would not have heard the one click. Still, I pushed the reset button. No change. Then, I jumpered around the inertia switch, running the wire disconnects through a 3A bladed fuse instead of the inertia switch. Same single click.

Fuel Not Pumping
what arrived
I concluded that the fuel pump, which had not been behaving consistently (sometimes just not working at start up), needed replacing. I slid under Oliver's backend and recalled that the original fuel pump had been replaced by the prior owner for what looks like a universal pump. I can't judge. Quite the contrary, I was not going to invest in a $200US+ original MG fuel pump on the assumption that the fuel pump is the problem either. So, I ordered a Spectra fuel pump from AutoZone for $48US delivered next-day-ish. This pump meets or exceeds the requirements for pressure (3.8psi) and delivery volume (18gph) for an otherwise stock MG engine. I sourced the requirements from this page on the MG Experience. The Spectra offers 2.5 to 5 pounds of pressure and 21gph, has reviews on Azn from MG owners saying they work great and even AutoZone shows these are a direct replacement for the Midget.

It is possible to over-power your carb with too much pressure, so that's one for the back of the mind while trying to diagnose what's going on with the fuel flow through combustion. I may introduce a pressure regulator, but one could argue that adding a cheap pressure regulator on top of a cheap fuel pump starts approaching the cost of a good stock-style replacement pump. While that's very true, I am not running a stock carb either. The prior owner installed a SK Racing (now known as OER) side-draft carb, which seems like a combination of the Mikuni PHH and the Weber DCOE, but this blog post has some great information about them. My knowledge of carbs is extremely limited, so I am accepting this as a learning opportunity.

Fuel Pump 2-Step
Holley Mity Mite
The pump that arrived was not as pictured. Lovely. This one was equipped with a 3/8" barb on one end and a 3/8" NPT female on the other. Into the 3/8" NPT, the consumer was expected to thread in the included mini-filter that has a 3/8" barb on the end. While I am sure a filter is needed, that one they included is tiny and virtually irreplaceable. Perhaps these pumps don't last past a fuel filter change. Since the pictures and the spec's I could see did not match, I was not going to go forward with it; I already have more than enough mysteries with the fuel system. I returned it unopened and got a Holley 12-434 Mighty Mite Electric Fuel Pump. These top-out at 4psi, push 28gph and actually ship with 5/16" hose barbs. Between the delays from CoViD and possible delays from that cargo ship that was blocking the Suez Canal for a week, the arrival of the fuel pump was not exactly immediate. Still, through the power of split-posts, it arrived in time to keep this blog active.
 
Fuel Pump Swap
The pump arrived mid-week, so I started my Saturday planning for the fuel pump swap. Over breakfast, I prepped the wires and assembled the pump and pre-filter. While the Spectra above also delivered with a filter like this, I know that Holley supports replacement pre-filters (I verified on their website). Either way, I figure I have one of those in-line clear filters just upstream of the pump, so I don't expect it to require service too terribly often. For the wire prep, I attached a male wire disconnect to the ground (black) wire and a male disconnect to the positive (red) wire.

ready for install
So, with the pump in one piece, and wire disconnects attached to the wires, I slid under the rear end of Oliver, bringing a collection of tools, a drain pan and a flashlight with me. I closed off the fuel supply from the tank with a small pair of vice-grips. I then moved from that hose forward through the fuel pump, disconnecting hoses and draining the contents into the pan. I only got as far as the pump before I didn't need to drain anymore. Clearly that old pump was not working anymore.

The MityMite is actually larger and heavier than the universal pump I had removed. So, I needed to adjust some fuel line lengths, but otherwise things just fit together. I reused the bolt hole which was holding the old pump to the front edge of the trunk, for example.Once all together, I wired the black wire to the grounding wire that was previously attached to the ground tab on the universal pump. Into the female disconnect coming from the pump, I put one blade from a 3Amp fuse. I put the other blade into the female disconnect which is ultimately wired to the inertia switch. I worked the disconnects with a pair of pliers to get the fuse to stay firmly in place. I wrapped the disconnects and the fuse with electrical tape. Last, I spooled up the extra wire and zip-tied it to the pump pre-filter so the connections would not shake loose.

Pump Test Fire
With everything as I thought it should be, I removed the vice grips and my tools from underneath. I turned the key to "RUN" and the pump fired right up. I left the key in "RUN" and checked the fuel lines for leaks. None appeared, so I concluded the pump was fine. Hoping for the best, I returned to the driver seat and tried to start the engine. Oliver would not start, but the engine would turn. That's a start. I removed a spark plug and I could smell gas on the tip, so We now have fuel and electricity. Next, we need to get electricity to the plug... at the right time.

Recall from my last post that my initial effort to find TDC were wrong, and that I needed to pull the valve cover to figure out true TDC? Well, I did that here. Still, even with true TDC found, Oliver would not start. I did figure it out, but that's my next post.

Thanks, as always, for following along--

Tuesday, April 27, 2021

MGB - Electronic Ignition

It was an unseasonably cold weekend recently. Since Oliver is in a nice warm-ish garage and Spring is supposed to be here now, I decided that I would start getting Oliver (1978 MGB) convertible-top-down, road-ready. Today's post starts us off with replacing the ignition. Like so many things with these old cars, nothing is as simple as it seems on it's surface, so this post ends without a running car. Maybe I'll get it next time. 

AccuSpark
Most folks think of "Pertronix" when they think of an electronic ignition upgrade. PerTronix makes great electronic ignition systems, for sure. I ran one on the old bus engine for a little while. I decided I would try the AccuSpark system because it was less expensive and appeared to be UK-based. The UK-based nature had me thinking that maybe it was better suited to an English motor. So, back in the Fall 2019 when I was thinking that I would be spending the winter finishing Oliver, I bought one of their kits, and put it on a shelf. Things happened, CoViD-19 blew up, the wiring in Hapy got complicated and I forgot about it... until I was cleaning my garage and found the box with the international shipping labels still attached. Jeez.

For around 70 pounds plus postage, you can order a drop-in ignition. When I did it, it ran me about $150US including shipping to the States. So, what's in the box?
- a pre-fitted electronic ignition in a 45D distributor (correct dizzy for a rubber-bumper / later model MGB)
- a distributor cap
- 4 Champion AC9C 3-prong spark plugs
- a blue ballast coil (though you can upgrade to a "Viper Dry" coil)
- a set of spark plug leads ("wires" to US folks) with a di-electric grease pouch
- you can optionally include a timing light

Preparation
It is recommended that you set your engine to top dead center (TDC) or firing position for the #1 cylinder. For most cars, the distributor could go in multiple ways, so making sure it is oriented correctly requires that you know which cylinder is ready to fire. The MGB engine is unusual in that it has a one-way-only key in the distributor drive and corresponding gear in the engine. If you try to put it in any other way it will not seat and not turn. Still, I wanted to make sure I had clear timing marks so I got a 1-15/16" socket for my 1/2" ratchet, removed the air-directing tin between the front of the engine and the rear of the radiator and turned the engine (clock-wise) until I could see the little nick on the rear of the main pulley. I aligned it with the top-most saw-tooth on the timing meter and then marked both with a dot of yellow paint. I also marked the tooth representing 15* advanced, since that is the stock amount of advance desired at idle (per the Bentley manual). This mark later turned out to be incorrect.
 
To find true TDC, I had to pull the valve cover and watch the valves move while I rotated the engine with the 1/2" ratchet. The mark that I believed was TDC was about 90* off. I found a different mark on the front (front is front) of the main pulley that was around midway between the points where the intake/exhaust valves opened. Accepting that this was the true TDC, I marked the nick with a dot of yellow.

With the replacement kit and tools on a nearby table, and the radio playing the Saturday morning KBOO shows, I was now ready for some ignition fun.

Spark Plug Remove and Inspect
My old ignition basically had not been looked at since I bought this car. Since Oliver has not had more than a couple hundred miles on him, clearly I did not drive his old system into it's current state. Frankly, it sat for a few years before I bought him, and without any servicing since, my expectation was that it needed, well... a lot. His performance had not been all that great when I bought him, and the new exhaust did not create the pick-me-up I had hoped for. So, away we go.

I started with removing the old spark plugs with a 13/16" socket. Spark plugs are a great gauge for how well your combustion has been performing: too rich, too lean, oily, too hot, etc. My findings were mixed, and odd. From firewall to fan, Plugs 4 and 3 were black, but dry, indicating that they had been burning inefficiently. Plug number 2 was black as well, but had some soot on it. Plug number 1 had a little bit of soot around the edge, but the prong was grey. So, I look at my plugs and compared them to the AutoLite Plug diagram (image posted here) to try to figure out what's going on.

Based on the mapping document here, numbers 3 and 4 are "carbon fouled", with lots of possible causes, ranging from "wrong plug" to weak ignition to mis-tuned carb, too-gentle driving or a bad choke. Neat, but at least they look like twins. I am more concerned about plugs from 1 and 2. These are fed by the same intake runner, yet they look very different. Plug 2 looks like a worse version of plugs 3 & 4, and plug 1 has a clean or normal looking ground electrode with some carbon around the edge.

L-to-R: plugs 4 to 1
These plugs may have been wrong for the engine. Spark plugs are a religion, and I have followed a relatively simple rule (that will probably frustrate / anger / enflame some people): I align the plug manufacturer country with the engine/car manufacturer country. So, I'll find NGK's for our Subaru, Bosch for Audi/VW's and Champions for US/English cars. The plugs I pulled out are single-prong NGK's; to be fair, NGK may make a perfect plug for the MG. I don't know. I can say that the AccuSpark folks (from the UK) sent me 4 Champion AC9C 3-prong plugs. MAybe they subscribe to the same flavor of spark plug religion that I do. I don't expect the plugs were the problem, but they may have been a contributor. Regardless, I gapped (0.035" per the Bentley manual) the three prongs on each plug and then installed the delivered-with-the-kit spark plugs.

Dizzy Swap
With the plugs done, I pulled the distributor cap and the lead from the coil. This created some access to the distributor mounting bolts. The prior owner installed a remote inverted oil filter unit, so the access to the front mount bolt was still a little challenging, but not impossible. Still, a little fun with an old-skool 7/16" spanner got the bolts out. Once the bolts were removed, the dizzy popped right out. I immediately settled it back in, and made a mark in the dust on the starter cover which direction the rotor was pointing. As I said above, the dizzy can only go in one way, so whichever way the rotor is pointing when you pull the cap is the only way it could be pointing. In the images I have seen on the internet, the number 1 plug is usually in the 1 o'clock position, but that is not always the case. Sometimes the dizzy gear is put in upside down so your #1 plug position is actually on the bottom. When I rotated the engine, the cap was on, and the leads had not been touched. I noted at this point, though, that the distributor rotor was pointing down and slightly to the left. When I removed the cap, the #1 lead was in that area, so I figured I would put it back together the same way. If things were 180* off, it will run, but poorly. Re-setting the leads 180* the other way would be easy to test later. I took the picture below so I could run the replacement leads the same way as they were.

old leads
With the old dizzy off, I loosened the clamp on the new one so it would move a little bit. The timing of the old set up might have been off, based on the "carboned" color of the plugs. Regardless, I want to be able to change it from the shipped-to-me state. I will clamp it tight (5/16" wrench) once the timing is verified. Satisfied that the dizzy would turn in the clamp, but only with some effort, I popped the new dizzy into place. The new mounting plate only had a single bolt hole for mounting, above and to the left, but otherwise, install was trivial. The lower bolt was the hard one to get to, so I was not going to complain. I put the now-extra bolt into the lower right hole anyway and snugged them both down tight.

Coil
The kit delivered with a new coil that corresponds to whether there is a ballast in your system. The electronics require the more powerful coil. Swapping a coil is easier than swapping a distributor, usually. In this case, because so many things leverage the mounting bolts for a ground, it is more of a juggling act than the coil swap in the old bus. I unmounted the original, and set it upright on the starter, leaving the wires attached to the various tabs. This gave me room to install the new coil and remain focused on the grounds and such. Once in place, I moved the female wire-disconnect-tipped wires from old coil to new coil.

Cap and Leads
The hard part, if you want to call it that, was over. Now, it was a simple matter of installing the leads. The prior set-up had the #1 lead around 7 o'clock. From there, they run the same way on all MG's: 1-3-4-2 anti-clockwise. The set of leads delivered with a clear dielectric grease, which is recommended on the electric connection to prevent corrosion and encourage a better current delivery. I smeared some on each end of all connections and plugged things in nice and snug. The electric connector floated around in the spark plug boot end a little bit so I made extra-sure the encased metal spark-plug end was definitely snapped on.

At this point, I would have started the engine and set the timing. Unfortunately, the turn of the key resulted in nothing. No noises, no clicks and definitely not starting. A quick glance at the voltmeter told me all I needed to know: flat battery. Awesome. So, this post got kinda long, and the resulting diagnostic did as well. So, I'll get back to Oliver next time. Thanks, as always, for following along--

Tuesday, December 1, 2020

Chasing the Hapy Electrical Gremlins (part 2)

Today continues where I left off with Hapy. Last, I had pulled a cable from the rear to the front, through small openings in the frame. I wired up the accelerator pedal plug into the new cable, as well as the ignition switch. Today, we take the next few steps.

Looking Up at 40F (4C)
Yes, it is still cold. It is December, after all. Now that Thanksgiving is behind us, the holiday music can come out in full force. Meanwhile, I'm dreaming of a not-rat's-nest wiring set up. Though, I suppose, a white Christmas would be pretty great too. We start with getting the wiring up front completely tidied up. I wrapped the exposed wires from the cable with 1/2" plastic wire wrap so it remains one cable almost all the way to the ignition switch. I split off the 6 wires for the accelerator pedal from the main bundle in front of the hand brake (front is front), and wrapped that in another plastic wrap. I ran that bundle behind the accelerator pedal support down to the pedal assembly. I then fed the excess cable down through the floor, leaving a little slack in the cable, but only just a little. The work in the cab is basically done for now.

Underneath
At this point, I slid under the front end and started sending cable back towards the rear. I was only able to get about midway before the original wire clump started to become a problem. See, I reused many of the same pass-throughs that I had used 10 years ago, and pushing the cable back against these wires was really not happening. So, recognizing that the old wires are no longer needed, I removed them. Unfortunately, they were taped to the 4-wire bundle for the brake switch, so I needed to remove that bundle as well. I wasn't using that circuit anyway: it only serves to notify the ECU that the brake has been pressed so turn off cruise control. I am obviously not using cruise control, so all of those wires go. I cleared wires all the way back to the spare-tire well, and confirmed the wire colors on the accelerator pedal circuit: they match. So, while the plug changed after the 1998 New Beetle TDI implementation, the wire colors didn't. Neat.

Lower Rat Nest Tear Down
Original outlet flange
Way back when I first did the swap, I had a Vanagon rear seat heater sitting on the accessory battery tray. That heater blocked from view how bad the wiring snarl was un the engine bay. Once the heater was removed this past Summer, it could have been obvious... if I'd looked. I did at this point in this rewire, and chose to start the cleanup right there. Hidden behind the heater were the relays and other associated wiring for the coolant glow plugs. For those not in-the-know, the manual transmission TDI's delivered with an aluminum coolant outlet flange. That flange had 3 glow plugs to warm the coolant. This flange was on this engine, but the coolant outlet sticks out the wrong side. In the bus, it sticks into the fuel tank. So, I swapped it out for the plastic coolant outlet flange that routes to the sides. Anyway, all that extra wiring and relay box were just sitting there. Were. They have been removed now. I moved a couple of ground wires that were in the middle of everything and then took all of the other wiring and pushed it up through the hole into the spare tire well. The cables that remain in the engine compartment are mostly against the compartment ceiling now. I didn't do much more, because I want the wiring up above to dictate how much more I do.

Research Again
It has been 10 years since I really looked at this wiring. Fortunately, TheSamba contributor AndyBees sent me a tome of wiring knowledge back then, and since I did not meaningfully stray from his work it will very much help me now. I barely scratched the surface of this documentation when I first did this install, though I did keep it in a 3-ring binder, with the other bus books in Hapy. 10 years ago, my goal was to just get it working and then I planned to circle-back and improve / clean it up. Well, after years of wrestling with the coolant (first leaks, then overheating) and then needing a break from the bus (hence, Oliver, the 1978 MGB), I'm only now getting to this. Based on a few hours of study, I expect I will be able to significantly reduce the remaining wiring. For example, I still have relays and wiring related to the radiator fan controls, even though I have those fans on a dashboard switch. And, of course, I will not be doing cruise control. There will be other discoveries as I go.

This is as far as I've gotten. My next steps are to start eliminating wiring related to functionality I am not going to retain (cruise control, etc). Since Hapy is outside/carported, this may take a while as I wait for nicer (read: warmer) days. We usually get a 50F/10C-degree day here and there. Since Hapy is blocking the garage bay where Oliver is parked, I may get my wrenching fix with some little projects on him when the weather is too cold to play with Hapy. Time, or more like weather, will tell. Thanks, as always for following along. Please stay isolated, and wear your mask / wash your hands when you can't.

Tuesday, November 24, 2020

Chasing the Hapy Electrical Gremlins (part 1)

In the Summer of 2019, we barely made it home at the end of the Dog Days 333 (See parts 1 and 2). Hapy decided to just not start on command anymore. He was dropping into that modified limp mode and it was happening not just when he was cold, but pretty much at random. I promised him that I would fix it as we sat idling in a Dundee convenience store parking lot while C was in getting us drinks. Today's post starts that "fix it" journey. Before I begin, for my US readers, Hapy ThxGiving. For CoViD's sake, please stay home.

One Last Time
Hapy parked in tarmac spot
Hapy's usual home
After I finished the priming of all the Zed body panels (See Zed Prime), I moved them into the garage. This freed a covered one-car parking space. I had initially planned to put Nemo back in there and get after his wheel bearings. I decided instead that with the CoViD-19 numbers climbing to all-time highs, maybe it was okay if I didn't have a car that could take me too terribly far. Nemo can get me to the corner store and back; that's plenty until I can get the wheel bearings done.. once I confirm that they are the source of the noise, and it isn't just loud tires. So, I switched it up, and I am instead jumping into the Hapy electrical. I could have gone after this stuff at any point during the nice warm summer. That just wouldn't have been consistent with all the other work that's been done on this beast, so of course instead I chose some of the coldest days this year to do it.

First, I had to get Hapy into the spot. He is usually parked on a tarmac strip at the curve of our driveway so we can see him out our bedroom window. Yeah, we're weird. For any other car, moving it would be a simple effort of start, drive forward, reverse into the spot. Once I got the other cars out of the way, it was his turn, and just like so many times before, he just didn't want to start. I turned the key to start and nothing happened. Sigh. So, I tried to push him. Nope. There's a little dip in the tarmac that he would roll back into. I had to pull him onto the concrete with a trucker's chain around his front sway bar at one end (his front tow hook was pancaked by the prior owner) and around Nemo's front end on the other end. Fun. While I was trying to figure out how I was going to push him back into the covered spot, I lamented out loud to Hapy "why can't you just start one more time?". His response: he started. Of course; good boy. So, I backed him into the covered spot, and turned off the key.

Running Cable
In the TDI retrospective about secondary electrical, I mentioned replacing the single wires I originally installed 10 years ago with a cable. Well, I bought 30 feet (~10m) of 12-wire 16ga cable for this job when I bought cable for the additional gauge (see Oil Pressure and Temperature Part 4). It is not quite as thick as my ring finger as a sealed cable, and it has a nice thick jacket on it. I figured that the computer and rat's nest wiring is on the driver (left) side, as are the accelerator pedal and ignition switch. So, running the cable along the driver side made more sense than running it along the other side. Turned out, I thought the same thing 10 years ago, as the old wire bundle ran that way. I started from the rear, threading the cable through the bottom of the spare tire well and down into the engine compartment. From there, I ran it through manufactured holes in the frame over the rear suspension, along the inside of the mid-section frame rail to the cross member near the new heater location. I pressed the cable through a square hole in the cross-member, under the brake booster and then through another square hole into the area covered by the front belly pan. I had bored a large (~1/2 inch diameter) hole at the very front over the Summer when I routed the heater fan control cable through. I had planned to reuse that hole for this cable, and it fit with very little trouble. I pushed and pulled about 5 feet of cable up through that hole so I could stand alongside the driver seat to do the wiring bits.

Wire Front First
The 12-wire bundle is more than I was really ready for. The accelerator pedal needs 6 of them. The start and run signals account for 2 more and the OBDII signal is the last. The other wires will be used in the future for things like a speed sensor and a glow plug light. Like the extra wire in the cable I strung for the oil temp and pressure for a low coolant warning, I'll get to those later. For posterity (and my own personal reference later), these are the circuits for the 12-wire cable. I will update this as I make changes or discover mistakes:

circuit wire color purpose
1 Red Accelerator Pedal 1
2 Yellow
Accelerator Pedal 2
3 Orange Accelerator Pedal 3
4 Brown Accelerator Pedal 4
5 Blue Accelerator Pedal 5
6 Black Accelerator Pedal 6
7 Red/Black Ignition - START
8 Blue/Black Speed Sensor
9 Orange/Black OBD-II
10 Yellow/Black Ignition - RUN
11 Brown/Black Glow Plug signal
12 Black/Red OPEN

I started with the ignition, splicing into the existing "RUN" circuit with the new signal wire. I figure the existing stuff (like lights) need power too, so the existing wire will simply feed old circuit #15. For the "START" signal, I just ran the new wire. The old starter signal was pretty batty, but it proved the TDI install was viable. Recall, it ran from the ignition down the old wire to right near the starter where it was spliced into a new wire that ran around the engine compartment to the spare tire hole through a relay to the computer, which then signaled TDI-donor relay to fire the starter... thru a new wire to the starter solenoid. There's like 20' (7m) of excessive and old wiring that I can eliminate. Then, I moved to the accelerator pedal.

Now, recall that I had to swap out the original round-plug accelerator pedal plug with a newer-model flat one after the old fly-by-wire pedal started to short out. I took a picture to help me identify which wire is which at the other end, but because the plug was changed, I expect the wire colors were as well, so when I cut the old wires off, I left about 1/2 inch of flat-plug wire on there so I can compare with the picture (here on the right) when I get to the rear-end wiring.

EDIT: I have updated the picture on the right here and the wiring reference above to reflect the actual circuit numbers in the wiring diagrams to avoid any confusion. Originally, the numbers ran the wrong direction relative to the official wiring schematics.

Even without the change, it was important to consider placement of the cable and the things that were going to be wired into it when I made my cuts to the wires. The ignition, speed sensor, etc are all at the dash where the accelerator is at the right foot. I made sure there was about 3 feet (1m) of cable between the ignition and the accelerator pedal cuts so there is room for cable routing. Also, it was important to pre-route the cable as much as I could so we didn't end up with the cable running in front of the steering column or goofy some other way.

Next
I admit, that doesn't sound like much. I moved the bus, ran some cable and did the wiring at the front end. Still, in sub 40*F (4C) it was a feat getting that much done without going numb. The weather around here is decidedly cold. I accept that I will not be able to get things done on Hapy very quickly, but with him out of the rain, at least it is not completely miserable. Just cold. If I can stand the cold, I will finish up the wire cable in the front by wrapping it with some plastic wrap, and pressing the excess cable back into the belly pan. Then, I'll push/pull the excess back to the rear so I have room to wire up the controls back there, probably leaving me close to 3m of leftover cable. There is a great deal of electrical housekeeping that I have not done back there. I think this is the right time to clean all that up, removing the unnecessary, trimming and mounting, etc so it is nice and clean. And, or course, our sporadic modified limp mode will no longer appear. It's all about staying warm enough to take small steps forward and eventually the wiring will be done. Then, I'll switch to diagnosing Nemo's rear bearings again.

Thanks, as always, for following along. Posts may appear more slowly as my work slows down. I'm still working on it (and staying CoViD safe, of course).

Tuesday, August 28, 2018

Hapy Rides Again

My last 2 posts have been about my efforts to resolve the electrical melt-down we had on the way home from 4Peaks. Today, we hit bottom and work our way back to operational.


No Start
With so many good signals, I wanted to try starting the engine. So, I turned the key to run and nothing happened. At first, this was because the wire to the starter (circuit 50) out of the ignition wasn't connected. Once that was solved, things got worse. I tried the start again and everything went dead. Nothing worked. I went around to check the voltage on the battery and it was crazy low, like 5V. Huh? While watching the voltmeter, it climbed back up to 12.5V. I checked other circuits and they started to show 12V too. By the time I had worked by way to the front of the bus, everything was working again.

I was able to demonstrate this a few times, and it seemed like no matter what wires I tested, I couldn't find a new burned wire. "Could the starter have fried," Boo asked. Why, yes. Yes, it could have. Since so much power routes through the positive post on the starter, the electrical fry that smoked between my knees could have caused a short there too. So, I pulled the starter and tried a ShadeTree starter test.

ShadeTree Starter Test
First, I checked for resistance between the positive and negative sides of the starter solenoid. It was infinite, which told me that the solenoid was probably fine. Still, I couldn't find a good recommendation for testing the starter motor on the internet. Most folks encouraged various tests while the starter was in the car. Mine was on the ground, and I wanted to test just the starter motor without all the other variables. So, I tried my own ShadeTree bench test. I grabbed an old battery that I had lying around. It had around 9V charge. That's enough to trigger the start, but not enough to do much else.

I took my jumper cables, and clipped one black end to the mounting ear (ground) and the negative battery post. I clipped one red end to the positive post on the starter and the positive battery post. I double checked the voltage. No change, indicating again that the solenoid is not blown. If it had been the solenoid, I would have expected current to travel through the starter all the time (solenoid broken with the current open) or none of the time. I worked the leads for the multi-meter into the clips on the starter so I could see how voltage changed when I triggered the start. Using a short section of insulated wire, I touched one stripped copper end to the positive post on the starter and the other stripped copper end to the trigger tab.

The starter did not fire, but the voltage dropped to almost 0. I immediately removed the trigger wire and watched multi-meter. The voltage climbed slowly, but steadily back to 9V. Yep. That starter got toasted, but the solenoid was doing it's job: open the circuit to fire the starter when 12V (or in this case 9V) is applied to the switch. I phoned over to the no-longer-local VW Friendly Auto Parts Store and they had one for me on the following Monday.

Assuming the starter was fried during the initial issue, replacing it should be fine. What if the starter was fried by my test-start because something else was still wrong? Then, the next test-start will cause the new starter to fry as well, right? Eek.

Re-Start-er
My fears, ultimately, were not realized. I swapped out the rebuilt Bosch I installed less than 3 months earlier with another rebuilt Bosch from Discount Import Parts (still only on the east side... and still not Hapy about it). I followed the instructions I laid out back then, and the test start provided the same disheartening click noise. So, I removed the starter and performed a very similar ShadeTree test. I used the battery and battery-to-starter cable from the bus for the positive side. I clamped a black jumper cable on the negative battery post and to the mounting ear on the starter for the negative side. Using the same little jumper wire from before, I triggered the starter and it fired. So, I haven't re-fried a starter and so maybe some of the wiring has been improved. But something remained. So, I looked at what was still an unknown around the starter while I re-installed it again.

Wiring
There's the 30 circuit (always hot) that runs to the front of the bus from the positive post and there's the trigger signal plug (circuit 50). I checked the 30 circuit first next because I felt it would be easy to rule it out. The 30-circuit is a red-with-white-stripe wire that runs from the starter positive post to the fuse box. In the Bentley book it is labeled as a "4" thick. That's in cubic millimeters and translated to AWG 12 (see my handy conversion reference here). The plastic on the wire near the fuse box was a little melted or swollen from the ignition failure, but I assumed (possibly a mistake) that it was just from being near the issues and that it was fine. To prove it wasn't an issue, I tried a few things. First, I did a continuity test to show that the wire didn't have a break in it. I believed that wasn't the case and the continuity test proved it. Resistance tests didn't show anything either (very low resistance). I didn't want to run voltage through that wire again, so I ran a long wire from the positive post on the battery along the ground under the bus through the driver door and into the same spot on the fuse box as the red-white stripped wire. This eliminated that wire from the equation as a variable. Then, I tried to start again. Just a "click" again. I tried swapping out the "50" wire that triggers the starter to fire. "Click".

Clumping the Circuits
In the interests of reducing variables, I considered the wiring as 3 large units or clumps.
There's "front-of-bus": that's the original wiring, including the ignition switch, fuse box,etc.
There's the "back-of-bus": that's the '98 NewBeetle engine related wiring. I include the battery in the back-of-bus not because its in the back, but because there are lots of wires routing to the NewBeetle stuff and only one heading to the front-of-bus.
Last, there's the "accessory" that is the deep cycle battery that powers the cabin lights. The accessory is completely separate, only connected by a common ground: the bus chassis. So, we rule that out.
If we consider that the front and the back only connect through a few wires, and I just tested replacements for them above, maybe we can unplug those and test. So, I disconnected the trigger wire for the starter (50), the always hot wire from the starter (30) and the signal wire for switched power (15) from the front-to-back connections, completely separating the clumps. Using my remote starter, I tried to start. "Click". From this, I concluded that the issue was not a front-of-bus problem nor a connection between problem. It resided squarely in the back. That's when Boo dropped by to see how things were going. "Could the battery have gotten affected," she asked. I had been checking voltage and it had been consistently 12.5V, but maybe there just isn't power (amps) behind that voltage. So, following that question, I put the battery on the charger.

Start
I left the battery charging at low amps (2A setting) overnight while Boo and I went to catch the new Incredibles movie. The next day, I re-set all my wiring was back at normal (front-to-back returned, nothing left unplugged, etc), and verified that the battery charger was complete. Everything looked good. So, I tried the new key. It fired right up. Ahh... much rejoicing.

Dollars and Sense
old housing,
melted and hammered
In the end, we add one starter ($160) to the total of the running costs from the last post, and we're approaching $1000. That's pretty darn expensive, but I can't say it was because of either owner neglect nor because of the engine upgrade. The interfaces between the front and rear of bus are very few, insulated with fuses or relays and weren't part of the problem. Ultimately, 50 year old wiring eventually fails. I need to commit to a complete rewire one of these days... but not while there's camping to be had this Summer. As to the total cost, if I remove the wiring harness I didn't need, the cost of the hotel that was just a bad timing thing and the steering wheel I chipped due to being dumb, this electrical repair cost me $295US ($85 for new housing and switch, $25 sub-harness, $25 headlight switch which is another whole story, $160 new starter) plus a $300 tow.

I do want to point out that the 2 major failures found along the way after the original ignition was solved were both identified by Boo. Obviously, she's amazing, but this also serves to illustrate something so important on projects like this: this is a team sport. You need input from a random friend leaning against the fender while drinking a beer pointing at stuff and asking questions. Or, a helpful wife wandering over with a lemonade innocently asking if the starter or battery could have been affected. I'm looking at trees, and she asked about the forest. Brilliant.

That's the end of the ignition smoked saga. While we may have missed String Cheese in the bus, it looks like our other musical (and simple summering) events can include Hapy. Thanks, as always, for following along.

Tuesday, August 21, 2018

Ignition Re-Assembly

In my last post, I described the tear-down of the ignition assembly of the old 1972 VW microbus. Today's post covers the re-assembly.

Some Part Suppliers Are Better Than Others
I mentioned that I found a bus wrecker in Washington who sold me a lock housing for $75 plus shipping. What I learned when I opened the box was that the lock housing came with an original key cylinder and key. The seller had stored the housing, cylinder and key all oiled up and in a zip-lock baggy. The key works the mechanism flawlessly. They included the small set-screws which hold the housing into the black box. Avery's Air Cooled, you rock. I wish I'd found you years ago. You'll be my first call now.

Lock Cylinder, Housing and Sub-Harness
new plug has exposed
solder so I taped it off
The Bentley has re-assembly instructions. I tried them. They didn't work. The book says to install the housing, then put in the lock cylinder and then, once everything else is in place, install the electrical sub-harness. Yeah.. that last bit doesn't work. The harness is constructed so that the wire bundle comes out to the side, not straight out. In general, that's good, but once you orient the plug to the housing, you realize that the wire bundle comes out the completely wrong way, running almost rear-wards. Holding the housing up with the plug facing you, it comes out around 4:30. Ideally it comes out around 9:00. So, to plug it in, and have it click home, the wires needs to double-back on themselves in a very tight area while you are somehow applying leverage for it to snug in. Physics just won't comply.

So, we do it differently. Before I started, I removed the lock cylinder from the housing and test fit everything. First the harness, then trying the lock cylinder first to see if there were any serious issues with doing the lock cylinder last. Nope. Since the harness was already wired into the bus, all of this was done using the driver seat as a work bench. So glad it's Summer, by the way. I plugged the harness into the lock cylinder and made sure it clicked home. There is only one way to get this all the way seated, with a larger tab fitting into the larger slot and a smaller tab into the smaller. I even tested whether the key, housing and sub-harness would trigger power, so I hooked up the battery and turned the key to the run position. I could hear the click-click of things getting juice, so I considered the test a pass.

Into Darkness
turn signal wire bundle
With the harness in the housing, we now twist into a pretzel to fit the housing into the black box. For reference, consider that the entire steering post, etc had been back together only to discover that the old housing wouldn't work. Recognizing how difficult the tear down was before (3 full days), I wasn't going to do that again. So, the black box is on the steering column with the rubber bushing, and such in place. The housing takes some fiddling to get into the right orientation, in part because the harness is plugged in, but mostly because it is not exactly parallel to the bottom of the black box. It tilts up to the right (towards the key opening). Once the tabs find the slots, you need to press the housing firmly as deep as it can go into the slots while tightening the set screws. This took a few tries, but once it was in the right place and the set-screws cinched down, I could start to see the light out of the dark

Key Lock
With the housing in-place, the lock cylinder can slide home. This is a do-it-once kind of thing. If everything isn't lined up right, and you need to pull the lock cylinder again, its a multi-day job. Things looked good, so I slid it home. It fortunately had no issues.

Other Discoveries
In my case, we believed the ignition fry was caused by either the heat/defrost fan or by the headlight switch. So, I removed the wiring for the heat/defrost fan and replaced the headlight switch. As happens these days, the headlight switch was faulty out of the box. I had to wire both the running lights and the headlights out of the same pin because the pin for the headlights simply didn't work. Also, the new switches don't come with a pin for the idiot-light on the dash, so I wired that into that same pin. Now, when I pull the stalk out one spot, the running lights, headlights and idiot light all illuminate. Nice.

While I was removing wires for the heat/defrost fan, I installed a new switched 12V wire along the same route. Following older VW coloring, I used black, and tied it into the furthest right fuse, the switched 12V for the coil used to come from. Now, when I turned the key to run, I have a nice strong signal for the new-engine electronics. But there was more darkness ahead. I'll get into that next time.

Thanks for following along. I'll wrap this up next time

Tuesday, August 14, 2018

Ignition Switch Teardown

This will be the first of 2 posts covering the efforts to resolve the damage caused during the electrical fire we had while driving home from 4Peaks (See 4Peaks 2018 - Road Report).

Recall... I looked down and smoke started first as a wisp and then as a billow from between my knees. We were fortunate to have a small road intersecting with the highway, so we dodged onto the shoulder at the corner, turned off the ignition and flipped on the hazard lights. I jumped out to make sure the hazards were on and saw the headlights were lit even though that switch was off. I went around back and removed the positive battery cable, thinking that the electrical was completely borked....

Roadside Findings
As I mentioned in the road report, we pushed Hapy under a tree. While Boo made peanut butter and jelly sandwiches, I twisted into a pretzel between the front seat and the steering column to see what was going on. The wires leading into the steering column were still hot. One of them was down to bare copper wire from just past the fuse box all the way past where my fingers could reach: a goot foot of plastic insulation had vaporized into smoke. I think if we'd gone much further without killing the electric, we would have either fried the battery or had the fire spread into the fuse box. Either could have spelled ruin for Hapy. As I said in that prior post, getting into the electrical solve required a 27mm socket to remove the steering wheel, so we got a tow.

Home-Drive Findings
160 miles (and $300US) later, Hapy was back in his usual tarmac-paved spot in front of the house. With the camping gear removed, and a good night's sleep, I was able to look at what was going on. My initial fears that my entire wiring harness had failed were not realized. I don't think. The sub-harness that runs from the fuse box to the ignition switch, however, was completely toasted. I concluded that the headlight switch was in need of replacing too, since the headlights flickered on the way to 4Peaks and were on without explanation when we broke down.

Extractions
I started following the Bentley to get access to the badness. Bentley documents this fairly well: remove the horn button and cancel ring, remove the steering wheel nut (27mm socket). Using a gear puller, remove the steering wheel, but they don't say anything about pushing the wire for the horn into the steering column. If you don't, the gear puller will probably cut it off for you nice and cleanly right where it comes out the steering column. Ask me how I know.

With the steering wheel off, you can remove the turn signal housing, leaving the turn signal hanging by it's bundle of wires from the black box. The black box is held to a silver support with 4 Phillips bolts. When these are removed, the steering column can pivot at the bottom. So, it is wise to remove the clip-ring, washer and rubber bushing. At least that's what Bentley says. The top of my clip-ring was so full of crap, I couldn't get to it. Also, that rubber bushing had never been off, so it wasn't inclined to move. Fortunately, the ignition sub-harness had burned so badly that it just fell out of the black box. So, the only things holding the steering column and wires was the column base and the wire bundle for the turn signal. The turn signal wires unplugged and the whole steering column came out as an assembly.

I had to loosen the black box from the column thru judicious use of a rubber mallet. First, I cleaned the top, removed the clip-ring and washer and shot lubricant around the rubber. It wouldn't give without a fight. Once apart, I could focus on getting the ignition cylinder separated from the housing. Now, the housing and lock cylinder were also original, so they had become very friendly. The housing removes (with the lock cylinder still attached) by removing these 2 little hidden bolts from within the rear-most bolt holes that held the black box to the silver support. With a little coaxing, the housing will come out with the lock cylinder still attached. The 72 and later (not sure about how much earlier) lock cylinders are held in with a small spring. This spring can only be compressed through a hole through the housing near the end where the cylinder goes in. This spring can also only be compressed if it hasn't been compromised. Mine was. Badly.

Pieces
I tried compressing the spring in the hole with various pokey tools. None would budge it. Lubricants couldn't do it. I finally resorted to drilling the lock cylinder like a safe cracker. It didn't matter. When I finally got the cylinder pieces out of the housing, the housing was unusable. The fire had melted some of the plastic inside and my man-handling of the housing and cylinder had made it's use uncertain. I figured I'd just order another one and be on my merry way. Uh... no. This housing isn't manufactured anymore. It's not on the internet enthusiast site classifieds. I found one on eBarf for almost $180 (shipped), but the seller wouldn't guarantee that it either worked nor that it would arrive within a month. So, I spent several hours hunting down small VW crackers, and found one in Washington who had one and sold it to me. $85US shipped.

Costly costly
So, the running tally for this mishap.... $300 for the tow home. $20 for that old switch I had lying around. $85 for a new housing. $25 for a new ignition sub-harness. I decided to replace the headlight switch, in case that was part of the problem, so add another $25. Add in the $180 for the complete wiring harness I bought but BusDepot won't accept as a return. Add in the $200 spent on a hotel for the shows in Eugene where we intended to camp but couldn't because Hapy was stuck in the driveway. Add $150 for a replacement steering wheel after I chipped my original during the extraction. AND, I haven't even done the assembly yet, so there may be more costs yet to come. Running tally: $785.

I'm ending this post genuinely more optimistic than I sound. This is an opportunity to improve lots of things as I go. The black box and the turn signal housing can get cleaned up so they look nicer. I can upgrade the steering wheel to one of those fancy wood ones for another $100. The key cylinder will be new so turning the key will no longer be a frustrating experience. All told, the ignition control and the area where I spend the most time will be much improved once this is done. Oh, and the engine will start and run again. So that's nice.

Thanks, as always, for following along.

Tuesday, July 31, 2018

4Peaks 2018 - Road Report

In my last post, I talked through the festival experience, omitting everything and anything that might have happened to Hapy. I decided that I would leave all of that for the road report: keep the road report about the bus and festival report about the festival. So, today's post is all about what happened on the way there, what befell the bus while we were there and what happened on the way home.

Getting Out of Dodge
view out the window the morning
after Vagabonding.
That's the Santiam River.
After last year's late-night drive to ChinookFest in Central Washington, Boo and I thought we should do it again. The drive itself was pleasant and fun (except for the emergency room part). The roads are empty at that time of night and the air temps are cool to help keep the bus cool. We work regular jobs, too, so we aren't ready to start packing until 7:PM or later so we have a choice of either waking up at home trying to motivate out early and hope to get to the festival early-ish -OR- leave crazy late and crash somewhere along the way, knowing that we'll wake and drive to the gate. I like option 2. This departure was similar to the ChinookFest exit in that we were leaving by 10. Just as we were pulling away from the house a freak thunderstorm hit, drenching us at the corner Safeway where we got ice and a few last minute things. We could hear the thunder deep inside the store, it was hitting so hard. For folks who don't live in the PacNW, this is very unusual. Storms like this don't even make the news in the MidWest, but here in the mild Pacific NorthWest it was all the locals were talking about when we got home 4 days later. We hit the road, and Hapy settled into the drive.

To Salem
We stopped in Wilsonville to grab some dinner, but the Black Bear was closed. So, we moved on until we saw a Denny's sign. Neither Boo nor I have been in a Denny's in years and hadn't realized they had a new budget menu. We both ate well and had a $14 total tab (plus tip). That's nuts. I don't know how they stay open with prices like that. Anyway, the engine temps had been climbing steadily since the Black Bear pull-over, and I discovered that one of the fan wires had shaken loose. Yep, that seems to happen every trip. A quick bit of fiddling and the fans were running, and we were back on our way. No sooner were we back on the road than we saw the OR-22 sign, and we were able to pull off the freeway onto the slower, easier state route. Though Hapy's temps still climbed on long uphills, they would settle back down when we hit a straight-away or downhill. I'd like to try to solve for the uphill temps by lowering the radiator an inch or two, but as you'll see by the end, I have bigger things to solve. I noticed that if I rotated the headlight switch to increase or decrease the dashboard backlight, the headlights would flicker a little bit. I made a mental note to replace the switch.

Vagabonding
It didn't take long before the late nights and early mornings of a typical work-week started catching up with us. Hapy, unlike his occupants, was doing great. We saw signs for Silver Falls State Park, and Boo exclaimed that she had never seen Silver Falls. Well, that's an Oregon icon that everyone should see when they visit, much less live here. So, we nosed off the highway and followed signs to the park. 30 minutes later, we arrived at a "campground full" sign. Too bad they don't post that, say, at the freeway turnoff. We found our way back to OR-22 another 30 minutes later, feeling all the more tired. We chased a few other signs before pulling over along the side of the road where there was a very deep shoulder (at 44.7673810N, -122.5331920W) just west of Mill City, OR.

After the original vagabonding during Almost Frog Lake (see part 2), we have this pretty well down. Well, Boo does. We free the bed by moving stuff into the front seats, cover the windows and crash for a few hours. In Oregon, the cops don't hassle you. We've talked to a few folks about this, and in the more remote areas, it is totally acceptable. I wouldn't suggest it in the cities and towns, but for places where OSP patrols. We awoke needing a restroom and coffee. We found both at a small roadside coffee cart on the north side of the highway just east of the Maples Rest Area. Coffee'd and with breakfast from the cooler, we were back on our way. We made great time past the reservoirs, over the pass, through Sisters and Bend to the venue. We arrived at 11:AM, an hour before the gate was supposed to open, but they waved us in anyway. Within a few minutes, we had our wristbands and were puttering up the hillside to the GoWesty camp zone.

No Charge Battery
When we were roadside, setting up for a night's vagabonding, I noticed that the cabin lights weren't terribly bright. I had put the accessory battery on the charger, but the battery acted like there wasn't a charge to take, so I removed the charger. I was starting to have second thoughts about that. After getting Hapy nice and flat, we set up and I tried to charge our phones. No dice. Then, the power converter would just beep at us, refusing even to light a very low amperage string of holiday lights. I checked the battery level and it was down to 8V. Huh? I figured that we could run cabin lights for a little while, but by the second night, we were on lantern lighting only. With all that solar energy coming from the sky, its a shame we don't have a collector. Something for the list, I guess. Fortunately, the 4Peaks folks have a vendor who provides a solar charging station, so we would spend an hour there in the morning, soaking up some sun ourselves while our phones charged up. It was because of the battery that these festival posts have virtually no pictures: I had no phone (and, therefore no camera) most of the time.

While we didn't have much electricity, Boo completed her camp shower vision at 4Peaks. I'll post independently about that since this post is already pretty long and we haven't gotten to the adventure part yet.

Where There's Smoke
With our stuff stowed and good-bye's shared, we left the festival grounds, filled up with diesel and headed towards OR97 and OR22 towards home. By now, it was mid-afternoon, and the hottest part of the day. The radiator kept up, though, keeping the engine temps under 196*F even on the longest uphill runs. Somewhere between Tumalo and Sisters I noted a whiff of smoke. I looked down and smoke started first as a wisp and then as a billow from between my knees. If this were a typical front-engine'd car, you would start thinking about engine fires. The only thing that far forward is the fuse box and the spare tire. Anyway, we were fortunate to have a small road intersecting with the highway, so we dodged onto the shoulder at the corner, turned off the ignition and flipped on the hazard lights. I jumped out to make sure the hazards were on and saw the headlights were lit even though that switch was off. I went around back and removed the positive battery cable, thinking that the electrical was completely borked. While I was around the back of Hapy, Boo headed off down the side street.

On The Tow Again
I paused for a minute, considering the heat of the sun, and what could I fix on the roadside. Then, Boo came around to me and pointed to a shady spot on the side of the road where we could push Hapy. And so we did. While Boo made peanut butter and jelly (PBJ) sandwiches, I pulled out the Bentley book and started looking at the wires. One wire had it's plastic completely burned off and a couple of others had swollen marks indicating they had been touched by heat as well. All of them fed from one side of the fuse box into the steering column. I figured the ignition wires were toasted, but to repair I would need to remove the steering wheel to get at the wire bundle. Removing the steering wheel requires a 27mm socket, which I don't carry in the bus, so we were stuck and contacted AAA. We sat in the shade eating PBJ sandwiches while we waited for the flatbed. It arrived about 2 hours after the first puff of smoke and we arrived home 3 hours after that.

Resolving to Repair
Years ago, I bought a replacement ignition switch. The original switch has been tempermental, not wanting to turn without considerable coaxing. I didn't want to go through the hassle of the install back then, so the switch has sat on my parts shelf. I ordered a replacement ignition harness from BusDepot. I will post about the replacement of the switch and harness effort once it's completed. In the meantime, we are in the heart of festival season and it looks like we may have to go to our first summer music event without Hapy since 2011. I sincerely hope I can get this fixed before the one after that. I'm looking forward to turning the key without challenge, and having all the smoke stay inside the plastic tubes.

Thanks, as always, for following along.

Saturday, May 26, 2012

Did I Stutter?

As I expected from all this daily driving, a new issue would arise.  Today is all about that.

Stutter
On the drive into work on May23 the engine suddenly shut itself off 3 times.  First as I was pulling onto Walker Road off the 217, again on driveway off Jenkins and last in the parking lot while I puttered looking for a spot.  Some quick research showed me that the main power relay (Relay 109) really sucks on these ALH TDI engines.  Apparently, folks buy them in bunches, and keep spares in their glove box just in case these things happen.  So, I ordered a couple from IDParts.com ($10 each plus shipping).  In my classic impatient way, I bought another one at Discount Import Parts (DIP) on the corner of Hall and Scholls Ferry Rd (Progress exit off 217).

Relay 109 Symptoms, but not 109
Thursday night, I tried swapping the relays, but the same effect happened.  Friday night, I tried some additional diagnosis with Boo listening while I tried starting / runing him.  As we talked about possible causes over breakfast this morning, she hit on it: it starts fine, but when you try to just run him, he dies.

Dang, it was me!
solenoid over zebra
striped rear of bus
I drove back to the bus this afternoon.  I grabbed one of the ignition relays that I put in to spook the ignition key action (see Inch by Inch) and headed for Radio Shack.  I got another relay there, but their supply of wire ends has turned to crap, so I hit O'Reilly's for wire ends (I got some heat-shrink too, but forgot electrical tape).  Back to the bus.  I started un-taping the wires from their respective ends and found 2 loose ones.  First, was the juice from the battery headed for the "run" relay.  Second was the connection between the 2 relay send signal wires and the one-way solenoid.  That one-way solenoid sends juice down to 2 of the 3 major spots, so this was a big deal.  Once these were repaired, the bus is road-worthy again.  I intend to return to the bus with the heat-shrink (and a lighter) and really seal up all of those connections.  With all the use the bus has been getting, it is crucial to have the wiring done for keeps.  This serves as a good reminder to myself: fab with the long term in mind.  Don't just do enough to get it to work.   Do it right enough so that it will last a while.  I put it that way because it is easy to over-engineer things for "lasting a lifetime", when you're just going to change your mind about things a few years from now.

Well, there's still daylight left, so I'm gonig to take a celebratory drive down the way to Taco del Mar to celebrate with a burrito.  As always, thanks for following along and more next time...