Hapy Home

This is almost a car post. Today, I get Hapy put enough together to move and then get him into the shop with his 2 brothers (Zed and Oliver) and sister (Nina).

 

Where Were We

Early in the Summer, like every Summer, I had big plans. Big plans. I was going to have my shop built and get Hapy fixed and then take all kinds of trips and such in him. Well, like so many prior seasons, my plans ran up against time and energy limits. It seems like every Spring I say "yes" to many things, forgetting that Summer is at-best 10 nice weekends here in the Pacific Northwest. We usually celebrate Independence Day wearing knit hats (still cold when it finally gets dark enough for fireworks) and some years Labor Day sees rain. That is the most extreme. Those with kids see summer's end around Labor day, but weather-wise, it is usually nice in September. So, to me, a "normal" Summer for nice weather planning runs from mid-July until mid- or late-September. 10 weekends. Maybe 12 in a good year. I committed 3 weekends to musical performances, had weekend family events in Eugene, Montana, Idaho and then in Seattle over Labor Day (7 weekends total). Just like that I'm down to 3 or 4 weekends for projects, cars and fun. In full transparency, we cancelled the Montana and Idaho obligations. I filled those weekends with digging trenches and laying french drain pipe, executing a storm water management plan I didn't have when the summer started. Still, when I look at the calendar through that lens, I now understand why Hapy sat in pieces. I am also kind of amazed that we got as much done, and not that surprised that we did not really do many "fun things" as we do other years.

 

sloped and cracked driveway

So, recall over Independence Day, I dropped Hapy's engine and tran-saxle so I could replace the chewed up flywheel (See Hapy Engine-Transaxle Dropped). When the new flywheel arrived, I popped it, on torqued it, set the clutch and bolted on the pressure plate. Once torqued, I struggled to get the trans-axle to mate with the engine. This was because of the few reasons, I think. First, the driveway is not flat, it is pitched away from the garage door, so getting everything level was more of a challenge. Then, the driveway is crumbling and heaved with large 1"+ drop-cracks in it. These cracks were larger than the wheels on the ATV jack I use to move and position the engine. So, once the engine was down and a wheel dropped into one of the cracks, I was no longer able to maneuver it front-back nor left-right. I could tilt it and raise-lower it. Even with those conditions, I got close, but the trans-axle fell off the smaller jack I had it perched on while attempting to mate. It landed on the driver-side output flange, popping it off the trans-axle entirely.

 

At this point, I was too frustrated to approach Hapy for a while, so I focused on getting the shop done. I decided that moving broken cars in the mud and rain was more objectionable than fixing Hapy in the rain one more time. If it came to that. I tried to find a mechanic to look at the trans-axle and re-assemble it. Instead, the D and M Automotive Service agreed to look at it and tell me how to fix it because he was convinced it wasn't beyond my skills and he had a 4-6 week backlog already. He was trying to close his shop for the weekend and subsequent vacation, but he took the time to show me exactly what I needed to do and fronted me the small bits needed to do the job. I still owe him $10 for those (facepalm). So, with instructions in mind and the required bits in hand, I headed home... and left the job undone ever since.

 

Prep to Move

Staying on the get-the-cars-outta-the-rain course, Boo and I agreed that getting Hapy into the shop was a necessary step before I try to re-assemble him again. The probability of failing again simply because of the driveway was too great. Before I begin, consider that the rear engine mount, the tower and the cross bar were out and on the ground. The engine was sitting on the ATV jack, but effectively on the ground. The boosted air circuit, fuel system and cooling systems were loosely hanging in the engine bay. Underneath, the axles were hanging from the wheel-end CV joints and the rear sway bar was detached. Hapy was nowhere ready to move a few inches much less 30+ meters (100'?) back into the shop.

 

in the lane way

I started with the rear engine supports by raising the engine up and connecting the rear cross bar. To this, I attached the tower (after de-greasing it) and then added the mount to the engine. The bolt holes in the engine bracket for the mounts were stubborn and I had to shoot the passenger-side hole with a tap before the bolt would travel the full distance. Last, I wrestled the mount holes over the tower holes and bolted the engine home. With the rear of the engine set, I considered how to suspend the flywheel end. I believe that when the full drive train is in, the upper trans-axle mounts are responsible for most of the support. These are on the trans-axle, of course, so I was concerned for how to hold the engine still during a move. I used ratcheting load straps, suspended from the body-side of the trans-axle mount and under the flywheel, slipping the strap between the flywheel and the engine so it would not slip off.

 

I used another ratching strap to suspend the axles. I finger-tightened the 4 front bolts of the rear sway bar, rather than nut them all the way down. Neither of these shade-tree hacks ended up being a problem for the move. Last, I suspended from the engine any partly-connected bits and removed all the loose fasteners and charged air hoses. Hapy was enough one-piece to move to the shop. We will see if any fasteners fell off when I get to re-assembly (LOLs). Visually, it looked good and walking the route afterwards I found no bolts, nuts or washers.

 

Homed

Hapy had been parked with his rear-end pointing south in front of the house. We needed his nose to be pointing south in the shop in order for his rear end to be pointing towards the big door (north). I wanted this orientation so I had the largest work area behind the engine as I could arrange. This meant we needed to turn him around before we sent him down the lane way. Boo and I went full old-skool. With her behind the steering wheel, I pulled the tire chocks and pushed the rear of the bus like the dickens down to the street. With a dog-walker stopping the one passing car for us, we kept Hapy rolling out the driveway and slightly up the street before I ran out of ability to push against gravity. Boo let Hapy roll backwards downhill just past the end of the lane way and over to the shoulder. I hooked up the trucker chain to Hapy's front frame and the other end to the ToyoTruck tow hitch. Then, we hauled Hapy all the way to the edge of the gravel before I had to peel away from the driveway in the truck. Because Hapy is heavier than both Oliver and Nina, I was concerned about the strain on the come-along. I moved Hapy about 6 inches and then decided to hold off and give it a think. I am not 100% sure of the load capacity of the come-along and I was uncomfortable with the amount of strain I put on it just for the 6 inches I got. That was Sunday afternoon. 

 

On Tuesday, Bill, our tree guy, arrived with a couple of employees to remove the failing cherry tree just south of the shop. Since Hapy was sitting in the lane-way, it was blocking the best path to the tree and the best path through which he and his guys could haul the pieces of the cherry tree to the chipper. So, in about 2 minutes the 4 of us pushed Hapy up into the shop. Shazam, Hapy is home. While I reeled from the gravity of what had just happened, Bill's guys backed the chipper to where Hapy had been sitting and got to work on the cherry tree. I still need to wiggle the rear end of Hapy west a little bit, probably remove the tow bar from the front of Nina, shove her further south and then shove Hapy further south as well to create more space near his rear end... but.. he's home.

 

---

 

Well, this ends the shop construction odyssey, at least until Boo and I find the cabbage to purchase doors. When we have solved for that and the final inspection has completed, I will accumulate all of the various costs and post the actual rounded numbers. If I had to guess, the structure was ~$25k, the concrete was around $15k, the permits around $2k, gravel, stone and french drain stuff was probably another $3k. So, my approximate running cost is around $45k, lacking doors. I will need to integrate a winch of some kind for moving broken cars and I still want to add a $5k lift. I don't know where that money will be coming from and I feel like I have already spent more than I intended to on the shop already.

 

Thanks, as always, for following along. Saving this mid-century farmhouse will always present me with projects, but once the weather shifts, I think my attention will as well... back to wrenching on cars.