ToyoTruck Saga Continues

Earlier, I posted about a new arrival to the fleet (a 2006 Toyota Tacoma XRunner) and the smash into a post that followed. Today's post is the next step in that saga. 

 

Where Were We

front assembled

We got a $5k repair estimate, but insurance wouldn't pay (because the agent screwed up). So, I ordered the parts, and set about doing the work myself. With supply issues, it took an incredible amount of time for everything to arrive and the largest part, the hood, arrived with a big dent in it. I successfully replaced the fender, the 6-piece bumper and the fender liner. The radio antenna was so corroded, it could not be removed, so I had to replace it as well. The hood scoop was also degraded, so I ordered another one of those. I ended the post while waiting for supply chains to support a new hood, as well as deliver the replacement passenger-side flare and the hood scoop.

Hood Gets Hammered

I decided I could no longer wait for parts while the new truck occupied my best work bay (read: prevented me from working on Hapy). Besides, there was no way to know how long it would be before a new dent-free hood would be available again. So, I decided that I would do my best to get the old hood straight enough to fit without putting pressure on the new fender nor passenger front headlight. I started with my angle grinder, removing the remaining paint from the dented area. The leading edge of the hood had been crumpled under, against a lateral bulge that rests just rearward of that edge, along the underside of the hood (see the picture on the right). Since the lip was forced against that bulge, I was unable to get a tool between the two.

the damage from the underside

I started with the stud welder and a slide hammer kit I got from Harbor Freight when I started working on Zed (1978 280ZX). With the 2mm tip and studs, I was able to slowly move the leading edge of the hood away from the lateral bulge. After about 30 minutes, and a dozen studs, the edge had pulled back far enough for me to fit a dull chisel against the leading edge. By moving the chisel up and down the lip, giving it a few smacks every few millimeters, I was able to further shift the edge away.

Once the edge had been moved about a finger-width from the bulge, I started shifting from the hammer/chisel on the lip to the stud welder / slide hammer on the top of the hood and back. My hope was that I could get some of the original hood contour back while I got the edge pulled. I spent about 90 minutes in total before I felt that it was close enough to set on the truck to see how close I was getting.

Old Hood Finish Up

time to try fitting

I was satisfied enough with the hammer work to move the windshield washer hoses and the seal. I figured that if I was as close as I'd hoped, I wouldn't want to remove the hood simply to put these bits on it. Like so many things, the first time always takes longer than any subsequent attempt. I had the bits moved in minutes. The hood set quickly as well. Some cars have a great deal of adjust-ability when the hood is mounted, but this truck does not. Yes, there is some, but not more than an inch left-to-right at the front edge. I did not need much to get the hood evenly spaced between the fenders, though.

Similar to the hood removal, I set the front of the hood on my old plastic tool box so I could get to the hinge bolts. Before I slammed the hood down, I checked the height between the headlight and the hood edge on both the driver and passenger sides to make sure I wouldn't break the light housing. I found that I had over compensated with my hammering, but only by 1 or 2mm. I started a recurring cycle of identifying where the gap was, opening the hood, adjusting, and re-closing the hood. After 4 or 5 of these cycles, I was satisfied that it was good enough for now.

finished enough

The stud-welder took it's toll on the hood, however. Some of the studs were welded on so well, that my efforts with the slide hammer resulted in a small hole in the hood. I own that, though: I believe that I held the trigger a touch too long on those studs, setting too strong of a weld. Some of the other studs would not come off no matter how hard I hammered them. I ultimately had to cut them off, but there were bits left behind. So, I pulled out the angle grinder again, and ground the dent-damaged areas of the hood smooth to the touch. I shot the polished metal with some rattle-can automotive primer and then some basic black Rustoleum. The final-for-now product is pictured on the right. That passenger flare will be installed when it arrives. I haven't decided about the scoop insert.

Weeks Later, It's Done

At this point, I felt done enough with this project. Yes, some part of what I put together will need to come back apart for painting and when the passenger side wheel flare arrives, I will attach it. One day, I hope to have a better hood, and when that day comes I need to install the scoop insert as well. Since I would like to have the whole truck painted, I may take it to Beaverton Auto Body and have them do it. We already have a somewhat dated estimate, but at least we know what ballpark they are in. Of course, with inflation these days plus all the extra parts expenses I incurred, a re-shoot could be prohibitively expensive. Expensive enough to bring that work right back to my driveway to be shot in my home-made "booth" later. Oddly enough, the extra parts (scoop insert, p-side flare, and antenna) plus a second and future $500 hood still will still be less in parts than the Beaverton Auto Parts bid. And that number includes a hood I can't use, and I have not tried to sell off any parts I got and did not actually need.

That's it for today. I will return to the hood when I get one, and otherwise I will be focusing on Hapy again. Thanks, as always, for following along-

Enter ToyoTruck

Super long post today, and I still didn't get the project all the way done in one post. I did get most of the way, though, and I'll wrap it up next time. For today, I'll hit some background first, and then get into the adventure with this new-to-us truck. Since this started on Christmas 2021 and today is the first of March 2022, clearly this has been quite a saga. At the rate this is progressing, it will be competed mid-Summer.

Background - the setup

example image

When C returned for winter break from University, he left his car ('09 Subie) on campus. He needed a car while he was home so he could get to work, but we have a significantly reduced the operable fleet (sold Flash, sold K'Lack). So, we borrowed-as-a-prelude-to-buy Boo's sister Rose's Toyota Tacoma X-Runner. I am referring it ToyoTruck for now, though the interweb folks often call these "taco's". I suspect it will get a better name when it presents iteself. Rose has an older Ford truck that is getting a new engine swapped in, so this Toyota was kind of extra anyway. Clearly, having extra cars around is a family thing for us, and with the rehab we plan on doing on this house, having a pickup readily available for supply runs will be valuable. Anyway, C arrived home a few days before Christmas, just in time for some radical winter weather. We got snow, and ice, and more snow, some sleet, and melting followed by freezing. It was a full-blown winter stew. We let C use Boo's '09 Audi A4 (all wheel drive, newer M&S tires, etc) while Boo drove ToyoTruck. ToyoTruck is rear-wheel drive with mostly-worn-down summer highway tires. That would have been fine if it weren't for the winter weather. With Boo's new schedule, she has to report by 7:AM, which means leaving well before dawn, and right about at the overnight low temperature. This lead to a Christmas morning (yes, she worked Christmas morning) sliding-on-the-ice scenario which ended with the truck smacking a pole. The passenger fender, the bumper cover, passenger headlight, passenger fog light, the leading corner of the hood and some assorted little bits all were affected by the very low speed impact. The damage seemed minimal enough that Boo continued on to work. It wasn't until the next day that we got to access the damage in the daylight.

How Does that Insurance Commercial Go Again?

after post-smack

In the daylight, it looked pretty twisted, but it is mostly surface damage. I took a bunch of pictures and we tried to get a claim going with our insurance company. Turns out that insurance goes with the car, not the driver, so we needed to use Rose's insurance. We learned this while we were getting bids (~$5k) on the work. This is where insurance got interesting: even though Rose told Allstate she wanted "full coverage" the agent pulled a massive boner and failed to include collision (pays for damage to your car). How that meets the definition of "full coverage", I don't know, but I swear this feels like one of their ads... where they say the competitor will leave you hanging with a tagline like "if you don't have Allstate...". It appears that the Allstate ad is actually self-describing. Maybe their ad should be more like "if you let our agents do it, you're gonna get screwed". So, to sum this up: we borrowed a truck, slid into a pole causing ~$5k worth of damage and there's no insurance to fix it. Happy Christmas.

Paulie: Bodyman

Fast Times Camaro

To resolve, I tried my best Spicoli imitation: "Relax, all right? My old man is a television repairman, he's got this ultimate set of tools. I can fix it." Of course, the next scene in that movie (Fast Times at Ridgemont High) has that car, unrepaired, but tagged with Ridgemont sucks / Lincoln rules spray-paint. Instead of that, I'm actually going to repair it. I took the itemized bid and ordered all of the parts the body shop said needed to be replaced from CarParts.com. This cost about $1300US delivered. The bid had the parts for around $2k, so we are already ahead in the game. I will simply remove and install the parts I received, and hope I discover nothing else is wrong. The labor for the body panel removal/replacement was $900US. So, if I can get the truck back into one piece, I will have saved over half the bid. At $900US, using my usual price for my labor ($50/hr for simple math), I break even at 18 hours. On its surface, I think I can get way under that. I had a great experience with CarParts.com, by the way. The bumper cover was wrapped in thick plastic wrap inside a huge box and the fender was made-in-Taiwan steel double-wrapped in custom cardboard protecting it plus packing material between the wrapped fender and the box sides. The packaging of the headlights was equally protective. Some of the shipping, however, was spotty. We can credit GLS for losing and then claiming delivery of almost half the order. Ultimately, they got the parts to me, 2 weeks after they said they were delivered. That final delivery was curious in that the box appeared without a text nor email update, though I had been set up for both. Sneakily done, GLS.

 

Finally, with all the parts I had ordered in my garage, I was ready to get started. I had finally gotten the 2016 Sprinter seats installed into Hapy (See Hapy Seating Part 2), so I could shuffle vehicles around. Hapy went back into the driveway and ToyoTruck moved under the canopy so I can work out of the rain.

Body Panel Removals

2 replacement bits in

I started by removing the front grill, fog lights and bumper cover. Then, I pulled the headlights and removed the fender, leaving the hood for last. The grill is held to the top of the radiator support with 3 Phillips screws across the top. Down below, the electrical plugs for the fog lights are simple tab-lock plugs. Since I am replacing the fog-lights with the bumper, I left the old lights in the old bumper. For reference, just press the tabs and they wiggle out. With the plugs out, the fog lights can push through the bumper (after pressing inwards on the plastic retaining tabs). The bumper cover is held on with plastic push-on tabs across the top as well as a few from underneath. These pop free with a slotted screwdriver. Since they are 15+ years old, they will often fail on removal. There are also a few 10mm screws as well, all from below. The ends of the bumper cover tie into the inner wheel well plastic, but eventually, once the last fastener is free, the bumper just wiggles free.

I next removed the under-headlight trim bits. There is a small plastic push-on thing, like the ones that held the bumper cover, on the inside that attaches the trim bit to the headlight, but the rest of it just clicks into place... or out of place. The headlights are held in place with long Phillips-head bolts from the top, and 2 more on the sides (one connects to the lower radiator support, the other through the side of the fender). The lights unplug, but if they are stubborn, the bulbs which are not the main beam twist out with a 90* twist. Then, the plug can be wrestled free. The last big thing to remove is the fender itself. There are obvious bolts from above, but there is one hidden in the door jam near the top and one from the outside just rear of the wheel well. Of course, before final removal, the inner wheel well needs to be removed, and the antenna needs to be dealt with.

 

super-glued tabs on the flare

 

The Inevitable Annoying Bits

The antenna and the inner wheel well skin are the worst part of this parts exchange. The antenna had become heavily oxidized and corroded, completely freezing the top nut. I ultimately broke-off the lower antenna mast so I could continue and ordered a top-to-bottom replacement, adding another $140US to the parts costs. Even on my garage floor, I was unable to separate the antenna bit from the bent fender.

The plastic inner wheel well is held in place by ribbed plastic clips along the inner edge and in a couple spots in the middle. Along the outer edge of the fender, the fender, the inner wheel well and the outer faring (flare) are held together with Phillips/10mm screws. When the truck hit the pole, the 3 top mount points along the outer faring / flare all broke. I did not realize that until I was removing things. Rather than order a replacement ($130US plus delivery), I collected the mounting ears and super-glued them back onto the flare as shown in the picture. Once the superglue had set up, the tabs did not wiggle. Since they broke off so cleanly, I could see their original pitch. So, I simply matched that and held the tabs for a 15 count as the glue set.

With the big parts out of the way, we can see where the little bits that Beaverton Auto Body suggested replacing. There is a small plastic bit that looks like a tiny fist with the hole in it that is Phillips-screwed to the fender. This holds the edge of the bumper in the right spot relative to the fender. There are 2 long thin brackets which support the top and bottom of the bumper cover (and lower leading edge of the fender) which were definitely tweaked. The small triangular bit that attaches to the passenger-side front (front is front) of the radiator support, extends forward to the other end of the long thin bracket, had a subtle twist to it. All of these attach with 10mm bolts, and you can see them installed in the picture above captioned "2 replacement bits in". They are the ones with big white labels.

Start Re-Assembly

windshield washer lines pre-removal

I started with the small bits: the triangular bracket first, and then the support bracket on the passenger side. I decided that the driver side bracket was untouched by the accident, so replacement was unnecessary. I swapped out the driver-side headlight next, re-using the original under-headlight trim bit since it was undamaged. Then, I tackled the fender. It is surprising how much faster install can be when you know where the fasteners go. I started with the 2 most difficult: the one on the bottom, heading straight in from the outside, and the one from inside the door. The bottom bolt is really only difficult because of all the extra lower body trim that appears on the XRunner needs to be loosened and held out of the way. I fear that I will need to completely remove all of the panels on that side because of all the dirt and sand I found in there when I took it apart. That dirt/sand may prevent a clean, tight install. Anyway, with the hard bolts in, I ran the bolts in along the top edge and then the front pair into the new bracket. I am not thrilled with the gap along the hood, but I will concern myself with that once the new hood goes on. It is possible that the hood got tweaked beyond just the small dent in the front corner.

After the fender, I installed the passenger-side headlight and the replacement under-trim. Other than cannibalize plastic fasteners from the bent and broken old body panels, this was as far as I could get at this point. I ordered a set of plastic snap-fasteners, but they had not arrived yet. Also, I had not planned for the antenna, so I could not completely button-up the fender and wheel well anyway. Yes, I could have stopped the post here...

The Hood

only disconnect needed

I was able to source everything, except the hood, from CarParts.com. For the hood, I turned to eBay, and got burned with a hood that arrived with a dent. My cursory inspection upon delivery did not detect that the passenger side had a couple of bashes in it under the cardboard wrap. I had checked the other 3 sides, so lesson learned here: completely unwrap the entire thing before you sign. I didn't know the pair of dents were there until I went to install it after installing the inner wheel skin down below, sadly. So, if I want a clean hood, I will order, pay, wait for and move-bits onto a second hood. FFS. Of course, with the supply chain issues around the world, there is a very small set of these hoods in the western US. In fact, according to the local Toyota dealer, there aren't any.

 

Obviously, the hood is held to the truck by 2 large hinges. Additionally, the windshield washer nozzles are in the hood. There are a few other things to transfer to the new hood, so I simply disconnected the washer hose and removed the bolts to free the hood. Then, I set the old hood next to the new hood in my garage. Piece by piece, with the puppy (Tuukka) watching, I moved the washer nozzles, bits of hose, the sealing rubber bits and the front rubber feet. Those feet are pretty interesting: they are solid rubber and thread in. You set the height of the closed hood by turning them clock or anti-clock wise. Very clever design.

 

There is a sealing strip that runs along the rear edge of the hood, held on by little plastic fasteners. I was able to free them without damaging them by using a door panel removal tool. I expected the washer nozzles and hose to the the hard part, with the scoop insert to be a breeze. It was the opposite, with the hose retainer plastic bits and the washer nozzles popping off with only a little difficulty, but remaining intact for reuse. These bits are held in place by little plastic barbs that need to be pinched in for removal. I used a slotted screwdriver, working one side and then the other until each one was free.

Hood Scoop Insert

The hood scoop insert, however, has seen better days. The mounting studs all backed out of the scoop, rather than allow the nuts to back off the stud. The 2 front studs would not separate from the old hood at all, and last, during install into the new hood, it cracked. This plastic is over 15 years old, and based on the damaged paint on the top of the vehicle and the sand I found in the wheel liner, I think we can conclude that this truck lived at the beach for a while, getting salt water on it while driving on the wet sand. I suspect it was parked outside mostly, as well, further accelerating the aging of the exterior. I will accordingly reset expectations for any other exterior bits I touch going forward.

I ordered a replacement hood scoop insert (another $140US for parts), and started considering doing a complete respray of this thing once the damage has been resolved. Of course, with the way I have to keep buying parts, that respray may need to wait a while. Meanwhile, I was in a holding pattern waiting for parts... and I was looking for a hood, again. Yes, I could have stopped the post here as well.

The Bumper

dry-fitting the bumper

The bumper cover / assembly is actually 6 distinct plastic bits: the main bumper cover, of course, a decorative center piece below the grill, 2 end pieces and 2 lower valences (split in the middle). Of these parts, we damaged 3: the main cover, the passenger-side valence and passenger-side end. All of these parts are held together with these blue wedge-like plastic clips. I was able to salvage all but one (which disappeared), which tells us just how slow moving the crash was. While I waited for parts, I re-assembled the bumper bits, excluding the decorative center. I had thought that I could paint the bumper as an assembly, but, I realized that I would need to take it all apart to install the decorative bit anyway, so I will be taking this all apart to shoot it. Of course, I put all this together mentally after I had put the bumper together physically. LOLs.

Still, by having the bumper bits together, I could dry-fit the front end together. Also, this reduced a big pile of parts in my small garage, and it helped me understand what bits I could sell-off, and which I still needed. For example, I discovered that there are little rubber strips between the main bumper cover and both the lower valences and the end bits. In the upper dry-fit picture, you can see the old valences on the ground below. A keen eye could see the rubber seals on top. I will be re-claiming those rubber bits before I dispose of the broken plastic parts. As you can also see. I have not removed the protective film from the lights yet; no need to tempt fate.

More Parts Arrive...

dry-fitting with the grille

After another week of waiting, things I ordered during the tear-down / re-assembly started to appear on my doorstep. So, I got back to it, starting with the antenna.

 

The antenna arrives with a stretch of cable that's about 1/2 a meter long with a pair of mounting clips already attached. This cable passes through the side wall and the fire wall up behind the glove box, and then runs up into the A pillar where it plugs into another cable. This seems like a strange design, but it's how it is. To access everything, the glove box needs to come out and the passenger grab handle needs to come out. There are a couple of plastic retaining clips that need to be popped (the OEM replacement antenna arrives with new clips) and then it is ready for removal. I attached a string to the end of the antenna cable and pulled it out through the side wall. I moved the string from the old cable to the new and pulled the string, bringing the cable along the original path.

 

The plastic tabs were in the right spots, and they popped in. The one in the rear of the picture below was a little difficult, but only because it is in a hard-to-get-to spot. I found by getting the front edge of the clip (front is front) first, allowed me to put pressure on the rear edge with a slotted screwdriver, snapping it home. Once the cable was in, the panels were installed in the order I removed them. The leading edge of the A-pillar trim inserts into a slot on the edge of the dash (seen in picture below) while the upper end has a tab that also fits into a slot: idiot-proof. The grab handle only fits into the A-pillar trim one way, and, because of the tabs, the mounting bolts align without effort. Inside the fender, the cable has a rubber grommet to seal the pass-thru hole. The top of the lower mast is then passed up into the hole in the fender and the lower end is bolted to a mounting tab with a 10mm bolt. After all the wrestling with German over-engineering, I really like this Japanese design. I feel like the Tacoma was built with owner maintenance in mind. I finished up the antenna on top of the fender with the outer rubber bit and nut and then threaded on the upper mast.

The Inner Wheel Well

installing antenna

All I had left was the inner wheel well, but I didn't explain the assembly of the rest of the bumper. As I mentioned earlier, I assembled the bumper, but I needed the bits to mount it. This was a straight-forward matter of using the plastic snap-clips where they belonged, and using the 10mm screws where they belonged. Since I failed to take quality pictures during tear-down, this was not as smooth as it could have been. Still, it all went together, leaving the passenger side wheel well. I purchased a replacement inner skin because I saw that the original had been damaged in the accident. The new liner was an exact match, and fitting it was not as terrible as installing on the old Jettas, but it was pretty close. These plastic liner things are the absolute worst. I did the outer edge last, simply because this edge also held the flare in place and I felt trying to juggle 3 things which were not in any way attached was at least one too many. The inner edge was straightforward: set the plastic skin where it is supposed to be and slam the plastic bit through the holes. The challenge for me was getting the square holes in the skin to consistently align with the square holes in the under-body.

With the skin now held in place by a handful of plastic bits, the outer edge was easier. I started at rear bottom and worked my way up. Again, having pictures would have been helpful so I could confidently set the skin / fender / flare stack correctly. Absent that, I just considered where water would go. So, I put the inner skin "outside" the fender along the rear edge for the first 3 fasteners (block water kick-up from the tires from getting inside fender) and at a cut-out transitioned it "inside" (so water drips from above don't run under the inner skin). At this point, I attempted to mount the fender flare. The super glue repair I described above failed almost immediately, so I shifted to the hood.... at which point I discovered the dents and my progress halted again.

 

I am going to halt this post here, and pick it up in another one. This has gotten very long, matching the saga, and the truck is still not in one piece. And, again, I'm waiting for parts.

Thanks for following along and more next time-

A4-ward Progress

Apologies for the late publish. Not sure what happened; I'll chalk it up to user error. Anyway, a few weeks ago, I mentioned that in a charitable move, I bought Nemo (the 1997 A4 1.8Turbo) from T (See If You Love...). Today, I go through the fixes I have done to get Nemo ready for someone to proudly drive, while avoiding work on Zed, the 280ZX. In an earlier post (See Dust Dodging), I mentioned the replacement of the window and the front side marker. I did a few less obvious things that I'll cover today. Before I begin, Hapy belated Labor Day to my US readers. Traditionally, this is the start of the most productive period in our calendar year: from Labor Day to Thanksgiving. So, if you feel like you're working a ton over the next couple of months, it's probably because you are.

Oil Leaks
Old Volksies like to mark their spot with a little oil. Old buses and bugs do it. Now that Jettas and Passats have been around long enough, they do it too. It seems that VW's German brethren, Audi's, mark their spot as well. For Nemo, there are a few sources. I focused first on the leaking motor oil. I slid under the front end, and after having sat for a few days, the oil that had been flung up from below during a drive had dripped away, leaving fresh oil only where it was actually leaking out. There was a nice big droplet at the oil drain, so I checked the torque on that bolt. It was a little loose. Next, I could see fresh drops on the cross member under the oil filter. It was hand-loose. As in, I was able to twist it tighter with 2 fingers. I think we found our main culprit. With oil filter pliers, I tightened the filter snug.

The power steering rack has a leak, and before I do another steering rack removal and re-install, I am trying the Lucas Power Steering Stop Leak first. This has been leaking since T bought Nemo, and T had been managing the level regularly with just topping it off with regular fluid. I intend to eliminate the leak. The steering is still really good and tight, though I expect the upgraded suspension helps with the road grip and cornering on rails. I looked back through my blog and I can't believe that I never posted on the steering rack remove/replacement I did on Flash, maybe 4 years ago. I think my dislike of the banjo may have started with those banjo bolts. It was a really tough job, so I'm all the more puzzled that I didn't post on it. Weird.

Dented Front Fender
With increased confidence from my efforts on Zed, I wanted to tackle the dent in the passenger fender. I pulled the front side marker, following the process I described in Dust Dodging. Through the hole presented when the light was removed, I fed a pry-bar. I did NOT leverage against anything, I just pushed/pulled outward and the dent popped out. My efforts left a small convex ding, but it is much better than the cereal-bowl sized dent that was there.

Under-Dash Panel

this is from an auto-trans, but similar

With the outside looking fairly good, but needing a wash, I started looking at the interior. There are a few things that need improvement, but I'll really only get after a subset. I started with the under-dash panel. T had removed this panel to replace the clutch master cylinder and had not re-installed it yet. We had the panel, but lost the fasteners. I made-do with things I found in the garage. During the install, I discovered that the remote trunk opener button was faulty, so I will need to replace that. Otherwise, the install was about what you would expect. The panel should be held on with 3 bolts, 2 through the front and one from the side, near the fusebox. Threading the bolts from the front is a great opportunity to practice patience. Gravity is working against you, and you can't see where the bolt needs to go once the panel is in place, so breathe deep and expect it to take many attempts. Once bolted into place, these panels are supposed to have 2 pop-in covers which fit over the bolt holes. I only found one so I'll add one of those covers to the junk-yard list.

Passenger Sunshade
The last thing I got after in this car-fix session was the passenger-side sun-shade. This was sitting on the floor since T bought Nemo. It looks fairly simple to mount. The plastic hook-looking thing goes in with the hook facing towards the rear, and you press up and back until it rotates flat, leaving the mounting hole near the hole in the steel above. At least, that's the theory. The prior owner had replaced the headliner and when he did, he mis-routed the wire for the light on the mirror. Instead of routing the wire through the hole in the steel where the mirror "hook" goes, it was left just dangling below that steel. So, the options were: don't hook up the wires to run the lights, return the route of the wires so it passes it through the steel from above -or- hack something. I didn't want to not hook up the light. I tried to figure out how to re-run the wires, but it appeared to require removing a considerable section of headliner because of the shape of the steel ceiling, so that left me with some kind of hack.

I took my hacksaw (aptly named) to the sunshade housing that, when installed, disappears into the ceiling. I cut a channel for the wire to slide down, reducing the mount of wire that would be pressed between the plastic and the steel ceiling. This actually worked, and I apologize for not taking a picture. Hopefully, you can see the shape of the mount from the picture on the right, here. With the wire pushed into the channel, I plugged the wire into the plug hanging from the hole in the ceiling. I pushed the rest of the wire into the headliner, and then followed the "theory" I described above. It pressed into place with not nearly as much effort as I expected. Once rotated around, I threaded a bolt through, and the sunshade is not in-place and operable.

The other bits of the interior that need to be resolved include fixing the cover on the driver seat cushion, and replacing some of the brittle plastic bits. I may not get to those items, but I think I will try to get the AC working; it probably just needs a charge. The next most important thing to resolve is the trunk is stuck closed. I'll get after that the next time I choose to focus on Nemo.

Thanks, as always, for following along.

You're Never Actually Ready for Paint

It's sort of like when you tell yourself that "maybe we'll take that trip next year". Or "maybe we'll do that bathroom re-model after the taxes are paid". "Maybe I'll go back to school after the kids are gone." Yeah. It's like that. What is? When you say "we're almost ready for paint". No, you're not; we have been saying "we're almost ready for paint" about this 1979 280ZX for almost 3 years. Today's post pulls the Zed out of storage and back into the workplace. First, let's remember some of the history of this thing.

Zed, a History

original CL listing

We bought it 3 years ago (come August) from a couple of guys who were turning it into a drift car. They made many dubious decisions like removing the center console, the little rear partition where the stereo speakers go, the sunroof (tack-welded and duct-taped on a piece of tin to fill the hole), the carpet, etc in the interest of dropping weight. They hacked up the ignition and wiring so the fuel pump, ignition and radiator fans are all controlled by switches. Of course, the switches don't match and they were installed kinda hinky, but they work. They did start with a great shell, though they painted a big purple V on the hood that just had to go. There is very little rust. In fact, there's hardly any anywhere on this thing. They did fold the driver door and fender, though. And, they did a top-end rebuild, so the valves still need to be re-gapped.

We bought a second 280ZX from a guy outside Seattle and had it towed home. This one was rusting apart, but it had a very clean grey interior, the center console and some other goodies, like original alloy rims. Our plan was simple: remove the interior, rims and other bits... then pitch the donor. The keeper would get a decent paint job (probably one that we'd do and learn how along the way), and then we would re-add all of the pieces. A replacement driver door was found during a separate trip T and C took into northwestern Washington. Unfortunately the yard was closing by the time they got there so they couldn't grab the matching fender. Oh, I almost forgot: this was my son's project. So, I was available labor, bur the decisions were his. The body parts were removed and hand-stripped either with chemicals or a grinder by C. Somewhere along the way, he either lost interest or became overwhelmed and the Zed was parked.

Out of Garage Storage
After shimmying along side the Zed, parked in the prime spot in the garage, for the next 2 years, I decided I needed to take more of a lead role. So, Boo and I pushed Zed back into the driveway. We are going to do everything we can to keep the Zed from returning to the garage in less than 1 piece. Zed hasn't been meaningfully looked at in months, so I spent a few minutes just getting re-familiarized with it. The fenders looks decent. The driver side has some small dents from where the fold near the driver door was hammered out. The passenger side looks straight. Both have a little rust along their bottom edges. The tailgate is solid, with some rust along the top edge. The hood is in great shape, showing no rust. A replacement driver door was originally a copper color, the outside skin had been stripped like the rest of the body panels, but the inside and edges were still copper. Overall, it felt like we could be fairly close to paint.

Still Not Ready for Paint

purchase day, passenger side

And yet, we're not. Over an exceptionally rainy weekend, I tucked into the 2 doors. I laid out cardboard, and starting with the passenger door, removed the glass, window controller and door latch mechanisms. Then, I re-sanded the outside with 100 grit and then 150 grit to get the skin smooth enough to an initial coat of primer, or filler if needed. The passenger door had a glaring imperfection at the door handle that I needed to bang out. Not having decent body tools, I made do with what I could pull together. In the end, I was left with a divot about an inch across (25mm) and about 1/4" deep. Because of where it is located, I can't get a good push angle from the inside. Anyway, I'll body fill that divot in stages so the filler dries correctly. I found some additional little pits that I can fill while I have the Bondo mixed.

The replacement driver door was in better shape, but it had a small horizontal outward fold about 6 inches from the bottom near the rear edge (front is front) that I couldn't see nor feel until I has the skin nice and smooth. That will be harder to get flat. I worked it with a rubber mallet, and that actually fixed most of it. There is, of course, more to be done before the doors are ready. These cars are so rare, the door rubber isn't available anymore. So, I am carefully removing the originals for reuse after paint. Once removed, the rest of the silver (passenger door) and copper (driver door) that would be visible after the door cards are returned will be sanded. Then, I'll do the body filler. Only then can I tape them for paint. Of course, the fenders (look at the driver fender in the original CL posting for an idea of the worst of it), the tail gate and the hood need similar attention... as does the remaining shell. So... it's gonna be a while before we're actually laying paint.

Ready is a State of Mind
In some ways, maybe this is like considering having a child: you're never actually ready for that either. Ultimately, you have the kid when you don't think you're ready, but maybe you actually kinda were; you were just scared. I think the same will be true of the paint prep. I painted houses for years, and if you are methodical and meticulous, you eventually get to the end. In both cases, it's about trusting yourself, and accepting that you're never ready and it's never perfect. At least not for your first few paint jobs... or your first few kids.

I can tell you that this effort will be consuming the next several weeks, and I have stopped all work on Hapy to make room to get this thing moving forward. I probably won't post much. But, then again, I have said that before and always managed to post anyway, so who knows? Regardless, thanks as always for following along.

Flash gets a facelift

Last week and weekend, T and I got the front end damage on Flash (the TDI Jetta) repaired.  Today's post covers that epic.

Accident Reminder
I should probably start at the beginning.  In mid-May, T was asked by his mom to drive his brother from their house in LO to my house in Beaverton for C's lacrosse stuff and then on to his 6:PM lacrosse game in Camby.  This led to 2 hours of rush-hour rubber-band driving, terminating in the chaos of intersections around Camby High School.  It was in one of those intersections, T got into an accident with an uninsured driver resulting in damage to the left-side fender, front bumper and the corner-edge of the hood (see picture to the right, here).  We left Flash like that for the next couple of months.  After buying and then changing our minds about a parts car (See: Welcome 2dot0), I re-doubled efforts to get Flash fixed.

Steal Your Face Right off Your, uh, Head
In a 95* garage last Tuesday, I set off to remove the damaged parts from Flash.  The shop manual is helpful for things like this, but it seemed like every "first" step was to follow a series of steps elsewhere in the manual.  Once the hood is up, the front latch is removed first by releasing the spring and then placing a slotted screwdriver into the Y and rotating it.  The plastic Y will pop off the nubs attached to the metal latch so it can be pulled straight out through the front grille.  The grille simply pops out by tilting the top forward.  If you still have your lower grills, they would be removed now; mine were lost in the accident.  Now, all of the star-driver bolts holding the front fender should be visible.  Remove the star-driver bolts from the bumper-ends which attach the bumper to the inner wheel wells first.  Then, remove the 2 lower bolts through the lower grille holes.  Last, remove the star-driver bolts accessible from above.  The bumper pops right off.

All of the above is necessary to just get to the fender.  But you can't take the fender off yet.  First, you need to remove the inner wheel well.  It is held on with more star-driver screws around the outer edge and one buried deep near the front strut.  Once you've wrestled the wheel well out of your way, the fender can be removed with a standard 10mm rachet.  The 4 bolts across the top are obvious.  There are 2 more at the front, and 3 buried at the rear.  The middle one of the "rear" on Flash had body filler slathered on it, so I had to dig that away first.  We discovered the plastic parts of the headlight were broken at this point, so we removed that too.

Searching the Yard
Wednesday, T and I drove Hapy to a wrecking yard, looking for body panels.  Turns out, Jetta's don't last in the yard too long.  One had been in the yard for just over a week and the front end was gone.  The others had been there longer and were even more picked over.  We did find a 1/3 rear-seat back, though.  The latch on Flash's had broken at Home Depot months ago, and was effectively locked in place.  Removing the replacement was easy: just pitch it forward, and with a screwdriver rotate the collar near the door to expose the opening.  Then, just tilt the back towards the center of the car, freeing that end.  The center just slides out.
For T, it was his first trip to a wrecking yard, and we had a blast.  He saw a few cars he had never seen before, like a late 70's Honda CVCC that he really liked.  While we didn't get the body parts we needed, it was still a good time.

IKEA-razy
The following night (Thursday), I got a response from one of my craiglist part queries.  Since he lived in the countryside outside Vancouver, WA, we agreed to meet at the IKEA near the Portland airport.  I took both T&C with me, and we got there a little early.  So, we went into the A/C to wander and wait.  The seller ended up about an hour late, but having not been at an IKEA for years, we had an unexpected tour.  They displayed a small-house set up of 590 square feet that all three of us found very interesting.  It seemed like every wall had storage solutions on it.  I remembered IKEA having much more disposable furniture made of veneer and glue-board than we saw.  What really tripped me out was how we walked in with no agenda, no real needs or wants, but by the end, we could feel the covet creeping in.  We found ourselves genuinely shopping for furnishings, and looking for particular things.  Fortunately, we recognized it, and quickly made for the exit.  We met "bumper buy" in the parking lot, accepted his bumper and pair of headlights for the arranged amount and headed home.

GTI Headlight != TDI Headlight
On Saturday, T and I started the work on installing the headlight and bumper.  Turned out, the headlights we got were GTI headlights, and the plugs were all different.  Additionally, the physical attachment point for the main headlight in the silver-flashy plastic was different.  We cannibalized the wiring and silver-flashy from the old headlight and the clear plastic and housing from the new-to-us one.  The head-lamp plug, though, couldn't fit through the housing, so I had to cut and re-wire a little bit.

Getting Hammered
Since we only had a bumper, we needed to make some ghetto adjustments to the fender and hood to fit properly.  Using an old spare tire from the bus as an anvil, I hammered on the fender to get most of the disfigurement out.  The rubber hammer and anvil worked really well, actually.  Don't get me wrong, it still looks bad; it just fits around the headlight, bumper and hood now.  At the end, I beat on the corner of the hood to get it to fit a little better as well.

As we did final assembly, we discovered that the front driver-side bumper mount/support was damaged in the accident.  Its a $20 part, but we didn't have it.  So, we put the front end together without it, knowing we'll need to remove and re-install stuff when we get the new fender anyway.  Also, the headlight housing and plastic screen need to be caulked to keep water out.  I need to do that before the weather changes.  I don't like the idea of the fender hanging out there anyway, so if I don't get a replacement fender soon, I'll swap out the mount/support and do the caulking anyway.

That's it for today.  Have a great weekend, and, as always, thanks for following along...